orionz06 Posted February 17, 2012 Share Posted February 17, 2012 The gun shoots 5"-6" groups with any ammo at 25 yards. The same ammo all prints 2"-3" groups with my G17 and me shooting. Who can I throw money at to make it better? S&W keeps telling me the gun is "in spec" which very well may be the case but "in spec" is laughable. Link to comment Share on other sites More sharing options...
saab Posted February 17, 2012 Share Posted February 17, 2012 Call S&W back and keep going over heads until you get the answer you want. I agree with you. This is NOT acceptable accuracy! Link to comment Share on other sites More sharing options...
trouble Posted February 17, 2012 Share Posted February 17, 2012 When you find out a solution let me know. Link to comment Share on other sites More sharing options...
Gary Stevens Posted February 17, 2012 Share Posted February 17, 2012 When you find out a solution let me know. I am having the same issue, but not at the extreme you are. Bar-Sto told me they would be producing M&P barrels in about 4 months. I will probably be on the order list. Gary Link to comment Share on other sites More sharing options...
orionz06 Posted February 17, 2012 Author Share Posted February 17, 2012 I have been on the phone with them. Most recently because the last time I got the gun back (last night) it was missing the locking block pin. It was apparently missing the pin and still acceptable accuracy wise. Not sure how much it shifts under fire but I can pull it a small amount without the pin in place. Link to comment Share on other sites More sharing options...
matgyver Posted February 18, 2012 Share Posted February 18, 2012 I have been on the phone with them. Most recently because the last time I got the gun back (last night) it was missing the locking block pin. It was apparently missing the pin and still acceptable accuracy wise. Not sure how much it shifts under fire but I can pull it a small amount without the pin in place. Totally Missing? As in it came back from repairs at the factory and was missing the locking block roll pin? I'd be calling and asking to speak with a tech on that. I will have to take a very, very close look at mine when it comes back. Link to comment Share on other sites More sharing options...
matgyver Posted February 18, 2012 Share Posted February 18, 2012 I have been on the phone with them. Most recently because the last time I got the gun back (last night) it was missing the locking block pin. It was apparently missing the pin and still acceptable accuracy wise. Not sure how much it shifts under fire but I can pull it a small amount without the pin in place. Totally Missing? As in it came back from repairs at the factory and was missing the locking block roll pin? I'd be calling and asking to speak with a tech on that. I will have to take a very, very close look at mine when it comes back. Mine came back today and looks perfect. I can't wait to get it out to the range and test it out. Thy even sent it back with a new mag in it...I didn't send any in since it had no feed issues. I reinstalled all my apex parts and I'm ready to shoot again. All I can say is be persistent and honest about your expectations. Maybe mention that you shoot it in competition. Link to comment Share on other sites More sharing options...
rack&roll Posted February 19, 2012 Share Posted February 19, 2012 A friend and fellow shooter had the same really bad accuracy problem with his new M&P Pro 9. We put my (9L) barrel in his gun and his gun shot great groups! He sent it back to Smith and they are sending him a new barrel. Hope this one is better. Link to comment Share on other sites More sharing options...
deerassassin22 Posted February 25, 2012 Share Posted February 25, 2012 I just got a M&P 9mm and have no issues grouping off a rest at 56feet nice 2.5inches groups and makes PF with no issues. Even shooting freestyle my groups stayed within about 3.5 to 4.0 inches not great yet shooting off hand but have had no issues shooting 124gr MG or Sierra Bullets with 6.6grns of HS-6. 4.7 grins of N320 and 115gr CMJ works great groups and also makes PF but is .3grns over recommended max load on VV website. Link to comment Share on other sites More sharing options...
Mr. W Posted February 27, 2012 Share Posted February 27, 2012 orionz06: I bought an M&P Pro last year and accuracy was not good. Take a magnifying glass and check the cut of the lands and grooves at your barrel crown. Mine was rough and inconsistent which would allow gases to escape incorrectly when the bullet left the barrel. Sent it back to the factory and it came back with a new barrel, and perfect crown. It is now very accurate. Link to comment Share on other sites More sharing options...
orionz06 Posted February 27, 2012 Author Share Posted February 27, 2012 Try this pistol-forum.com/showthread.php?2903-Recent-manufacture-M-amp-P-9-accuracy&p=55467&viewfull=1#post55467 Link to comment Share on other sites More sharing options...
Utah Shooter Posted February 27, 2012 Share Posted February 27, 2012 Call S&W back and keep going over heads until you get the answer you want. I agree with you. This is NOT acceptable accuracy! Being in customer service for over 10 years this technique does not really work. Here is a good read on customer service call. http://www.cracked.com/blog/5-idiotic-misconceptions-about-calling-customer-service_p2/ OP I hope to hear some good back from this experience. I myself am looking at getting a S&W and hope to hear that you are at least satisfied with the end result. Link to comment Share on other sites More sharing options...
orionz06 Posted February 27, 2012 Author Share Posted February 27, 2012 Word is I will be getting a new gun upon their receipt of the current one. Link to comment Share on other sites More sharing options...
Petrov Posted March 6, 2012 Share Posted March 6, 2012 The gun shoots 5"-6" groups with any ammo at 25 yards. The same ammo all prints 2"-3" groups with my G17 and me shooting. Who can I throw money at to make it better? S&W keeps telling me the gun is "in spec" which very well may be the case but "in spec" is laughable. I think I ran into you on another forum,I mentioned it there I will mention this to the rest of the people so they dont get burned. I have a problem with my M&P not shooting worth shit at 25 yards and striker leaving gouges drag marks on the primer. Sent it to smith, they test fired at 15 yards told me that it was within spec. So basically I have a 600$ paperweight. Link to comment Share on other sites More sharing options...
dsa Posted March 6, 2012 Share Posted March 6, 2012 Is there anyone out there that has sent there M&P back to S&W for accuracy issues and been satisfied with it upon return? Link to comment Share on other sites More sharing options...
orionz06 Posted March 6, 2012 Author Share Posted March 6, 2012 Is there anyone out there that has sent there M&P back to S&W for accuracy issues and been satisfied with it upon return? I have been told I would receive a new firearm. In the interim I have located an LE gun that shoots quite well, I will meet with the agency and use their good ammo, my laser, and a rest to put a few through their paces and see what we come up with. I am confident S&W will correct the issue long term, just up in the air short term. Link to comment Share on other sites More sharing options...
matgyver Posted March 7, 2012 Share Posted March 7, 2012 Is there anyone out there that has sent there M&P back to S&W for accuracy issues and been satisfied with it upon return? Read my post above. I am more than happy with the outcome. I recommend that you state your expectations cleat with the rep. Be honest if you have non factory parts (apex) and if you can remove them before shipping. I had modified my trigger bar an requested that it be returned to me if replaced. I received the gun back, with a new mag, my trigger bar in place, the slide and barrel replaced, and sighted in with a site that brought POI to POA. Very happy. Link to comment Share on other sites More sharing options...
open67 Posted March 19, 2012 Share Posted March 19, 2012 I had similar results from my 9L when I had it. S&W had me return it and received it back saying it was within specs. Very disappointing to say the least. Kept at them and did talk to a rep that said this should not be happening and that they would make it right. Sent me out another barrel with same results. Reported it to them and they sent me another prepaid label. Before I could sent it in received another barrel but this one looked different. Previous two looked like there is a ring between the barrel and the block while the last barrel is just the block which now is bigger. Fits tighter in my slide and shoots better. Went from 6-8" groups at 30yds. to 3-4" groups at 30. Bought a Dawson fiber optic front sight to correct for it shooting low. Not great but now is acceptable. Have been waiting for the Bar-Sto barrels from Apex. Randy at Apex I believe said that S&W has not made there locking surfaces tight enough and the Bar-Sto will have 2 barrels. One, semi-drop in and one a full pistol smith fit. Some one correct me if I'm wrong. Would try another after maket barrel but if they take factory specs don't know if I would get much better results. Really like the pistol. With apex trigger parts, great trigger. To good as a matter of fact. Comes in at 2lbs. 10oz. Will have to put in the factory return spring to make it production legal in 2013 looks like. Link to comment Share on other sites More sharing options...
MarkCO Posted March 19, 2012 Share Posted March 19, 2012 To good as a matter of fact. Comes in at 2lbs. 10oz. Will have to put in the factory return spring to make it production legal in 2013 looks like. No, the rule change to 3# in Production was recently voted down 9 to zero: http://www.uspsa.org/uspsa-online-mtg-details.php?meeting=30&type=meeting Link to comment Share on other sites More sharing options...
Sin-ster Posted March 19, 2012 Share Posted March 19, 2012 A World Champ was kind enough to shoot mine a few weeks ago for accuracy. Over 20 yards, free style, at a 1.5x1.5 inch black 'X' on a metric IPSC facing at a 30 degree angle. A clover leaf of 4 rounds, and a single shot about 1.5" higher. I'd say my gun (with my load) is accurate. After Dan did my trigger work, he function checked the pistol @ ~60 yards on an 8" rock. 17 hits "as fast as he could get them off of the sights". At the very least, it illustrates that not all of them are inaccurate. Link to comment Share on other sites More sharing options...
Petrov Posted March 28, 2012 Share Posted March 28, 2012 My M&P has been back to the factory twice, the refuse to fix the accuracy problem, correction the refuse to acknowlege it. Link to comment Share on other sites More sharing options...
orionz06 Posted March 28, 2012 Author Share Posted March 28, 2012 My M&P has been back to the factory twice, the refuse to fix the accuracy problem, correction the refuse to acknowlege it. Their spec is less than 2" groups of 3 shots at 10 yards. If it meets that there is no problem, in their eyes. Link to comment Share on other sites More sharing options...
Petrov Posted March 28, 2012 Share Posted March 28, 2012 My M&P has been back to the factory twice, the refuse to fix the accuracy problem, correction the refuse to acknowlege it. Their spec is less than 2" groups of 3 shots at 10 yards. If it meets that there is no problem, in their eyes. Yep, yet at 25 yards I have rouds hitting the target holder not even the target or the paper it is printed on, offhand, rested,sandbagged, had another guy shoot it too with the same results. VERY frustrated as I am basically out of 600$ thanks S&W Link to comment Share on other sites More sharing options...
orionz06 Posted March 28, 2012 Author Share Posted March 28, 2012 How does it shoot at 10 yards for you? Best thing to do is call them and talk to someone. Post on their Facebook as well, let the world know as many ways as possible. They won't fix it if only a few people here and there are pissed. Link to comment Share on other sites More sharing options...
saab Posted March 28, 2012 Share Posted March 28, 2012 After I put in a KKM barrel, my groups went from 4-5" to 2" if I do my part. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now