theKenny

You would get better/quicker replies if you post in the correct forum. 3 gun nation is not USPSA shooting. This sub forum is for USPSA, though I guess USPSA multigun would technically apply. On the website they say they follow USPSA rules,practiscore is what we use to score it, the procedural are USPSA procedurals. Where is the right place for clarification? Load to division capacity is a maximum, no minimum IMO. Not Load to. WSB is Loaded To https://s3.amazonaws.com/MS3GNUploads/Stages/WalkThrough/1g350nhy.hje.jpg?w=712&mode=crop and by 3GN rules its a procedural under 3.3 3.3 Additional +5 Seconds: Shall be assessed for failure to start in the position indicated in the Written Stage Briefing.

Dawson https://dawsonprecision.com/basepad-hicap-for-para-extended-tool-less-design-by-dawson-precision/ read here first https://cdn6.bigcommerce.com/s-5t3ceeio/product_images/uploaded_images/paramagtubedimensions.jpg?t=1445692892 If the tubes are too short these mags will work http://gregcotellc.com/cart/index.php?main_page=product_info&cPath=160&products_id=1612 I'm using these with the dawson basepad Or get a few SPS or MBX I have both, both work.

http://tarantacticalinnovations.com/

How do you not lock it in? just rest it in the holster? correct. trigger guard is still covered

I really like my Safariland Duty Gear 578 7TS Pro-Fit GLS Med Frame Long Slide Multi-Fit Right Hand Holster, Blackhttp://www.safariland.com/paddle/model-578-gls-pro-fit-holster-with-paddle-57800.html http://demandware.edgesuite.net/aaqv_prd/on/demandware.static/-/Sites-tsg-Library/default/dwfa4650b9/product-pdfs/holsters/Safariland_578_Pro-Fit_Fit%20Guide_Owners_Manual%20030215.pdf good review here: if I'm not moving at the beginning of a USPSA stage i just don't lock it in. For 3gun i know its not coming loose.

If you want to run a shotgun with less than division capacity I don't think anyone is going to give you a procedural. If you want to run a single stack in open I don't think anyone is going to care either Wsb says loaded to. Rules for the division define capacity.

Stage was a 3GN Classifier. in the WSB it states: "Standing inside Box-A, Shotgun loaded to division capacity and held at port-arms, safety engaged. Pistol loaded and holstered, safety engaged." So from that statement if you are in practical or factory division shotgun should have 9 shells loaded.

Full tears in both shoulders. Right (dominant) repaired. took almost a year. I second Neomet's advice. Still have to get the left done, been putting it off for several years.

These will work in the Pro Custom 16.40with Dawson Extensions http://gregcotellc.com/cart/index.php?main_page=product_info&cPath=160&products_id=1612 as will these http://spsshop.es/cargadores-paraordsps-enduromac-c-26_38.html?language=en&sort=6a these are actually 134?mm you can run the TTI 7mm basepad on them and it should be legal but I have not gauged them yet I've run both without issue

What he said.

The Micromoa 16 rifle has a .101 port (45* angle) The 17.3 has a .93 port More info here http://micromoa.com/16-17.3-rifle-gas-competition-setup/

Disclaimer: I know the owner and a buddy or two is sponsored by them. i bought mine after seeing their results and shooting their rifles Other guys I know run the barrels from 12.5 to 17.3 All are very accurate with factory ammo I'm running the 16 mid with wolf gold and was ringing plates out to 600 meters (limit of scope) last weekend Another buddy (not the guy above) was ringing steel out to 550 with a 12.5 I have the Govnah gas block tuned for 2 loads (hoser and long range) and the 3rd position is full open gas. For next year i'm picking up one of the 17.3 Rifle

Thanks for reminding me Bamboo-Para 9/40 slides have the same breechface. I've been meaning to try one of the Tanfos

I had a Rock Island. Actually 2 First was replaced by the factory. While OK it needed a lot of work. Thumb safeties throat barrel mag well Mag tuning canyon creek mag catch for sti mags and it still was not 100% reliable. Bought a Para p18 when the rebate was active and never looked back. For 9 and .40 mags mbx or sps or sti. Ramped barrel. Only thing need was to swap out recoil spring and guiderod. I have another one I'm building up for limited. I'd give the nod to Para over RIA.

Thanks for the info Flas.h

Welcome. Not sure what the good Carolina is but Tarheel 3Gun is one of the best run monthly matches. http://tarheel3gun.com/ Lots of good shooters up there

Looks good, Tempted to do mine one day. OP, did you gauge those mags with the 7G basepad to see if they are legal? I have several of the SPS myself in 9 and 40 and the stock basepads definitely have to go. I've just been using them with the 3G pads but was planning on the 4Gs and no I do not have a guage. Thanks

OP, Call Universal and see if you can take a class from Manny before he leaves at the end of the year. I hope the guy posted below does not mind. Stage plans for the same match are better. He finished 16th in Limited

Squadding Link https://practiscore.com/fort-benning-multigun-2015/squadding

Way to go Raleigh!

Is that the complete list for 2016? There seems to be a large regional hole for the mid Atlantic area, or most of the center of the country. Starting about 18 min

3GN Regionals Feb 27-28 Florida - Universal Shooting Academy April 9-10- Alabama - Brock's Gap Training Center May 14-15 - Texas - Copperhead Creek Shooting Club June 18-19 South Carolina - Clinton House Sept. 10-11 Utah - Southern Utah Shooting Sports Park October 22-23 Virginia - Virginia International Raceway - NATIONALS

Finally got around to shooting this. Low 3.88 High 5.35 4.615 Average. Pm Sent for part 2.

han my Will it fit Gen4s with the grip inserts installed? The product description didn't specify and I do like the way they look! I don't have one. I did try a gen3 on someone's, seemed fine though no faster or better than my dawson ice. I saw somewhere maybe FB that it does not fit with backstraps. Since I Use the med beavertail I'll stay with the dawson I'm sure you could modify the backstrap to fit though.

Taran's Gen4 is out http://tarantacticalinnovations.com/index.php?main_page=product_info&cPath=44_80&products_id=322