• Content count

  • Joined

  • Last visited

About cvincent

  • Rank
    Looks for Target
  • Birthday 12/13/1982

Profile Information

  • Gender
  • Location
    Surprise, AZ
  • Real Name
    Cody Vincent

Recent Profile Visitors

287 profile views
  1. I would still take out the shock buff and try it. The extractor in my infinity is the same way to remove. It's not an aftec. Sent from my iPhone using Tapatalk
  2. I have a few times with success, until now I have one that's stuck. And I'm kinda scared to try and remove it. Sent from my iPhone using Tapatalk
  3. That seems very strange. I've been using Around Black Friday they offer free shipping in 5 gallon buckets. That's when I order. Can't recall any cases being cracked front the batch. Maybe a couple after firing, but Doesn't even matter at that point. Downside is I get quite a few .357 sig in there. But machine sorted I assume. Whatever. Still a pretty good price. Sent from my iPhone using Tapatalk
  4. That was Tiffany on the phone. She is very helpful. Everyone at infinity is very helpful. Did you tell her it is a factory SV gun? If it is.. I inquired of this same service a few months ago. It's 450$ install, fit and refinish. May require a new grip safety. Sent from my iPhone using Tapatalk
  5. I get this same issue. But not nearly as bad and intermittent. I believe it's the nature of the Redding CSD. "Alignment and accuracy are enhanced by the cartridge case and bullet being completely supported and aligned in a close fitting, precision ground sleeve before the bullet seating begins." The bell is being removed by the "close fitting, precision ground sleeve" before the seating of the bullet occurs. The same thing can happen with the Lee die as well, if the die body is screwed down a lot Sent from my iPhone using Tapatalk
  6. 10 rounds at 100. 23 grains 8208. 77 grain sierra TMK. 18" JP barrel. Shot some steel at 500 with this load. Dinging 8" plates all day. Flyers could be me. I was using a rear bag and the MBX magazine base pad wing stabilizer things. Sent from my iPhone using Tapatalk
  7. Maybe the PT aggressive and infinity aggressive are quite different. I just got an infinity aggressive and in a match it's great. Repetitive dryfire, it's a little sharp. I wrapped it with tape last session. Worked good. If you go aggressive you can always bead blast or sand down the sharpness, as stated. Sent from my iPhone using Tapatalk
  8. Maybe your dummy rounds are too long. The projectile is getting stuck in the lands. Sent from my iPhone using Tapatalk
  9. Same as Steve. I leave the droppers and output springs on the tool heads and just remove from the collator. Less than 10 mins to change everything from .40 to .223. Sent from my iPhone using Tapatalk
  10. I have only used the teardrop button. But, I do find myself hitting the top of the button, where the checkering is, when I hit the button. So I don't think I would like the circular button. Sent from my iPhone using Tapatalk
  11. I love it. I can't go back. I shoot right handed. Just put an Infinity grip on an edge for the right hand mag release. Sent from my iPhone using Tapatalk
  12. Ah hah! Tapatalk search sucks. Went to google and found it. Sent from my iPhone using Tapatalk
  13. What is the problem with the frame? I just installed a new SV micro pocket grip on an edge and my infinity mags don't work, nor did they work with the plastic STI grip. Sent from my iPhone using Tapatalk
  14. my SV mags dont work in STI plastic grip either. new style mags. i would just get the SV tubes. fill with grams followers and whatever base pad you like. SV base pads require a hex key to remove. the complete SV mags with their internals will only hold 18 or 19 rounds. with grams internals. you get 20 reloadable all day
  15. #7

    I used #5. worked fine, just had unburnt powder inside the gun. unless I had too, I wouldn't use it again. I'd imagine #7 would be worse. Sent from my iPhone using Tapatalk