hummerbk Posted September 5, 2023 Share Posted September 5, 2023 Does anybody have a way of washing a speed loader while at the range, maybe using something like a golf ball washer? I shot an IDPA match and my speed loaders were picking up so much sand that it eventually started interfering with my rounds dropping into the cylinder. A couple of times I could see sand grains on the brass cases. One or two would hang up about a quarter of an inch and I'd have to push them down to close the cylinder. I tried blowing them out with compressed air but the sand seems stuck in the holes. I wash them at home and dry them in the oven on low but after two or three stages they are full of sand again. Link to comment Share on other sites More sharing options...
Joe4d Posted September 5, 2023 Share Posted September 5, 2023 maybe buy a few more ? Link to comment Share on other sites More sharing options...
Farmer Posted September 5, 2023 Share Posted September 5, 2023 Is it like static is attracting and hanging onto the sand? If you’re washing them there shouldn’t be any oil film on them. Might have to dust them with mica or something similar. Link to comment Share on other sites More sharing options...
hummerbk Posted September 5, 2023 Author Share Posted September 5, 2023 It has to be static holding the sand in the six charge holes. it has to be washed and brushed out because compressed air won't do it. I heard that a soap film will reduce static so the last time I washed them I swished them in some soapy Dawn water and dried them. It didn't make any difference. The sand adheres to the sides of the holes and some will transfer to the case near the rim causing my issue. Do you think talc might work. Most of the mica is colored. Link to comment Share on other sites More sharing options...
Pseudonym Posted September 5, 2023 Share Posted September 5, 2023 Check if your wife has any dryer sheets and give the loaders a wipe with those. That should knock the static down on the plastic and then try the air to clean off any dust. The static will return, so if the dryer sheets work, pack a few in your range bag. Link to comment Share on other sites More sharing options...
Toolguy Posted September 5, 2023 Share Posted September 5, 2023 Look for anti static spray on Amazon. There are many different ones. Link to comment Share on other sites More sharing options...
10mmdave Posted September 5, 2023 Share Posted September 5, 2023 Quart Tuperware container with some light soapy water and a can of compressed air maybe ?? Don't forget the drying towel for your hands. With the carts I see in use at shooting matches whats one more thing or two to lug around Link to comment Share on other sites More sharing options...
pskys2 Posted September 5, 2023 Share Posted September 5, 2023 1 hour ago, 10mmdave said: Quart Tuperware container with some light soapy water and a can of compressed air maybe ?? Don't forget the drying towel for your hands. With the carts I see in use at shooting matches whats one more thing or two to lug around keep thinking a recliner would fit? Link to comment Share on other sites More sharing options...
hummerbk Posted September 5, 2023 Author Share Posted September 5, 2023 Dryer sheets, mica, anti-static spray, Tupperware. All great ideas. I was sure I could get some help here. Link to comment Share on other sites More sharing options...
rowdyb Posted September 5, 2023 Share Posted September 5, 2023 It's expensive, but I've seen guys treat them like moon clips and bring enough of them loaded and ready to go, such that they never re-use one. The same with loaded magazines, I've seen people do as well. At a local you'd need what, 22 to ensure you never had to re-use a dropped one for a six stage match.... Link to comment Share on other sites More sharing options...
Toolguy Posted September 5, 2023 Share Posted September 5, 2023 You could get your gun cut for moon clips and use them if the rules would allow it. Link to comment Share on other sites More sharing options...
MHicks Posted September 9, 2023 Share Posted September 9, 2023 Anyone try one of the spray cleaners that are supposed to be safe on Polymer/ plastic? Link to comment Share on other sites More sharing options...
RePete Posted September 18, 2023 Share Posted September 18, 2023 You could carry a can of compressed air to blow them clean. FWIW I have about 27 speedloaders (Safariland) and have never cleaned them in 35 years - no issues. Been dropped in sand, gravel and grass. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now