Rdelawder Posted November 26, 2019 Share Posted November 26, 2019 I have 9mm Trojan that's ready for new springs. Can anyone recommend a good set up for USPSA single stack minor. I have been and running reloading147 gr Extreme with 3.2 gn of titegroup in my cz and would like to stick to this recipe. Any recommendations would be greatly appreciated. Link to comment Share on other sites More sharing options...
223to45 Posted November 26, 2019 Share Posted November 26, 2019 Since every gun and load are slightly different, you may have to play around with springs.But in my STI single stack I run a 8 lb recoil and 15 lb main. YMMV Opinions will vary too.Sent from my SM-G930V using Tapatalk Link to comment Share on other sites More sharing options...
grsdoug Posted November 26, 2019 Share Posted November 26, 2019 9 lb in my Trojan for exactly the same load. 8 lb felt sluggish in cold weather. Link to comment Share on other sites More sharing options...
jcc7x7 Posted November 26, 2019 Share Posted November 26, 2019 Like 9lbs to close the slide a little quicker and no slide dip. 19 lbs main for slightly quicker hammer fall and ignites all primers. Link to comment Share on other sites More sharing options...
shootin-blanks Posted November 26, 2019 Share Posted November 26, 2019 I run 10# and 17# in all my 9mms Link to comment Share on other sites More sharing options...
tdp88 Posted November 26, 2019 Share Posted November 26, 2019 1 hour ago, shootin-blanks said: I run 10# and 17# in all my 9mms This is what I ran in mine and it would pop any primer and was very flat. Link to comment Share on other sites More sharing options...
Shorty4087 Posted November 27, 2019 Share Posted November 27, 2019 My friend and I are both running 11# variable recoil spring for a similar setup on 147 and 135g Link to comment Share on other sites More sharing options...
Rdelawder Posted December 1, 2019 Author Share Posted December 1, 2019 On 11/25/2019 at 9:14 PM, 223to45 said: Link to comment Share on other sites More sharing options...
Rdelawder Posted December 1, 2019 Author Share Posted December 1, 2019 Thanks for the feed back on what works for your Trojan's Link to comment Share on other sites More sharing options...
MickB Posted December 1, 2019 Share Posted December 1, 2019 10lb Wollf variable rate recoil spring with 15lb or 17lb mainspring. Mick Link to comment Share on other sites More sharing options...
Rdelawder Posted December 3, 2019 Author Share Posted December 3, 2019 Thanks Mickb Link to comment Share on other sites More sharing options...
jpm2953 Posted December 3, 2019 Share Posted December 3, 2019 10lb recoil 17lb mainspring Link to comment Share on other sites More sharing options...
Rdelawder Posted December 12, 2019 Author Share Posted December 12, 2019 Thanks again for the feedback. Heres were I'm at. 15 lbs main spring (everything goes bang) 10 lbs with a new Dawson Precision capture guide rod. This set up has helped, but I still have reliable issues with feeding and ejecting. I am going to look at the extractor next. Has anyone found their extractor to be the problem with reliable issues with the Trojan? Thanks in advance for additional feedback. This has been fascinating for me because the gun ran great for a couple years. Link to comment Share on other sites More sharing options...
GringoBandito Posted December 12, 2019 Share Posted December 12, 2019 Extractor issues can certainly crop up from time to time and looking at the extractor tension is probably a good idea. If you are looking for a low cost and awesome replacement, take a look at the EGW practical extractor. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now