darks1d3 Posted September 11, 2019 Share Posted September 11, 2019 This is probably a dumb question but I'm going to ask anyways. Is it ok to reseat an already loaded round? I just need the round to be about .02 shorter. The round is loaded light so the extra pressure from a shorter OAL isn't an issue. I just loaded a ton of rounds for my 9mm 1911 so I loaded them a bit long. Got a new gun and the longer round doesn't quite plunk. I only have a square deal B so it would save me a ton of time just reseating the rounds I have. Link to comment Share on other sites More sharing options...
Rnlinebacker Posted September 11, 2019 Share Posted September 11, 2019 This is probably a dumb question but I'm going to ask anyways. Is it ok to reseat an already loaded round? I just need the round to be about .02 shorter. The round is loaded light so the extra pressure from a shorter OAL isn't an issue. I just loaded a ton of rounds for my 9mm 1911 so I loaded them a bit long. Got a new gun and the longer round doesn't quite plunk. I only have a square deal B so it would save me a ton of time just reseating the rounds I have. yep just don't load it into the primer station and you'll be fineSent from my SM-G973U using Tapatalk Link to comment Share on other sites More sharing options...
stick Posted September 11, 2019 Share Posted September 11, 2019 Yes you can safely reduce your OAL by re-seating the bullet. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted September 11, 2019 Share Posted September 11, 2019 Sounds like you're good to go, but I'd run just a few and test them out before I ran a batch of 100+ of them. Link to comment Share on other sites More sharing options...
darks1d3 Posted September 11, 2019 Author Share Posted September 11, 2019 Sweet. Thanks guys! Link to comment Share on other sites More sharing options...
bwikel Posted September 11, 2019 Share Posted September 11, 2019 If they are coated or plated bullets pull one after you re-seat them to assure you aren't removing the coating or plating as you seat them deeper. Link to comment Share on other sites More sharing options...
Yondering Posted September 11, 2019 Share Posted September 11, 2019 (edited) 1 hour ago, bwikel said: If they are coated or plated bullets pull one after you re-seat them to assure you aren't removing the coating or plating as you seat them deeper. This. It's usually fine to seat jacketed bullets deeper. With any sort of lead or plated, if the rounds were crimped very much you'll probably have issues with shaving lead/coating or cracking the plating. This is the same reason why we don't seat and crimp in the same step. If you didn't crimp very much it may be OK. Edited September 11, 2019 by Yondering Link to comment Share on other sites More sharing options...
darks1d3 Posted September 11, 2019 Author Share Posted September 11, 2019 Yes they are plated. I crimp just enough to take the flare out around .3765 on a 124gr 9mm. Link to comment Share on other sites More sharing options...
2tuf4u Posted September 11, 2019 Share Posted September 11, 2019 Reseating is occasionally done by benchrest/target rifle shooters who believe cold welding occurs between the jacketed bullet and case neck when ammunition is reloaded and stored for a " lengthy " period of time prior to being fired. Some reloaders intentionally load the rifle cartridge "long" specifically for this purpose. Link to comment Share on other sites More sharing options...
cas Posted September 12, 2019 Share Posted September 12, 2019 Taper crimp, not so bad. Roll crimp, not so good. I once loaded 1500 rounds that I had to reseat. So like a fool I reseated about 1400 of them. Only to find the new COAL still wasn't short enough and I was still getting squibs. The next time I only did a few hundred.... which I ended up still being too long and I ended up doing them yet again. lmao (Using up a big box of .356" 115gr JHPs, loaded into .38 special cases with a very light charge. Way too much empty space.) Link to comment Share on other sites More sharing options...
Yondering Posted September 12, 2019 Share Posted September 12, 2019 7 hours ago, 2tuf4u said: Reseating is occasionally done by benchrest/target rifle shooters who believe cold welding occurs between the jacketed bullet and case neck when ammunition is reloaded and stored for a " lengthy " period of time prior to being fired. Some reloaders intentionally load the rifle cartridge "long" specifically for this purpose. Yep. It's also a trick to use when pulling bullets; if they are really hard to pull, seating them a little deeper often breaks that bond between the neck and bullet so they'll come out easier. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now