ysrracer Posted May 4, 2019 Share Posted May 4, 2019 Sorry, I couldn't figure out how to edit my original post from my phone. I had an opportunity to try out a BMT Mooner for my SW 627 in .38 special. It's a cool little gizmo. It seems well made. However with Remington .38 special ammo and TK .25 thousands moon clips, it's a little too difficult for my 61 year old hands to turn it. Full disclosure, I never dug a ditch, or put in a hard day's work in my life. It did work well with the .38 Colt short ammo, and the clips that Mark brought with to try out. My verdict is, try it for your specific application before you buy it. I won't be buying one. Link to comment Share on other sites More sharing options...
revoman Posted May 4, 2019 Share Posted May 4, 2019 You can remove one of the pieces of metal that put the rounds in and also the side that takes them out. Then you are only putting 1 round in or out at a time it makes it easier. Link to comment Share on other sites More sharing options...
ysrracer Posted May 4, 2019 Author Share Posted May 4, 2019 Years of viewing "adult content" on the internet has left me with carpal tunnel syndrome in my right hand Link to comment Share on other sites More sharing options...
pskys2 Posted May 6, 2019 Share Posted May 6, 2019 (edited) I found that the 1st few loadings of "new" tight moon clips were almost impossible to load with my BMT without help. The help I used was to put a couple of screws to lock the base onto the bench. That helped give me enough leverage to load them. As they smoothed out it became easier, so that I could do it without the extra leverage. Edited May 6, 2019 by pskys2 Link to comment Share on other sites More sharing options...
357454 Posted May 6, 2019 Share Posted May 6, 2019 (edited) I have found it helps to load four rounds at a time, takes a little longer but much better than anything else out there. Edited May 6, 2019 by 357454 word insertion Link to comment Share on other sites More sharing options...
ysrracer Posted May 16, 2019 Author Share Posted May 16, 2019 I've since found out that there are two different models. One for rimmed cartridges that loads them two at a time, and one for rimmless cartridges that loads them one at a time. The one for rimmless cartridges that loads them one at a time has the added benefit of having more leverage. Link to comment Share on other sites More sharing options...
mchapman Posted May 16, 2019 Share Posted May 16, 2019 (edited) 19 hours ago, ysrracer said: I've since found out that there are two different models. One for rimmed cartridges that loads them two at a time, and one for rimmless cartridges that loads them one at a time. The one for rimmless cartridges that loads them one at a time has the added benefit of having more leverage. If you look back up at post from May 4 from revoman, he is telling you about the one for rimmed cases and is suggesting that you may want to remove one of the two teats that load two at a time to make it easier for you. Edited May 17, 2019 by mchapman correction Link to comment Share on other sites More sharing options...
KrakenFan69 Posted May 21, 2019 Share Posted May 21, 2019 I've used mine for my 627 for 2 different matches. My left hand got bruised and swollen after each 2 day event. I tried loading 4 or even 2 at a time but at this point I think I may have to find another solution. I am hoping that my 20 moons will get worn in enough to make the loading easier but we will see. Kraken Fan #69 Link to comment Share on other sites More sharing options...
PatJones Posted May 22, 2019 Share Posted May 22, 2019 I've used mine for my 627 for 2 different matches. My left hand got bruised and swollen after each 2 day event. I tried loading 4 or even 2 at a time but at this point I think I may have to find another solution. I am hoping that my 20 moons will get worn in enough to make the loading easier but we will see. Kraken Fan #69What moonclips and brass are you using? Link to comment Share on other sites More sharing options...
ysrracer Posted May 22, 2019 Author Share Posted May 22, 2019 (edited) 10 hours ago, KrakenFan69 said: I've used mine for my 627 for 2 different matches. My left hand got bruised and swollen after each 2 day event. I tried loading 4 or even 2 at a time but at this point I think I may have to find another solution. I am hoping that my 20 moons will get worn in enough to make the loading easier but we will see. Kraken Fan #69 I'm confused, the one I used you put in all eight cartridges in at the same time. You clicked it four times, because each click loaded two rounds into the clip. There was no way to load four at a time on the one I tried. Edited May 22, 2019 by ysrracer Link to comment Share on other sites More sharing options...
KrakenFan69 Posted May 22, 2019 Share Posted May 22, 2019 4 hours ago, ysrracer said: I'm confused, the one I used you put in all eight cartridges in at the same time. You clicked it four times, because each click loaded two rounds into the clip. There was no way to load four at a time on the one I tried. Only load 4 round into the mooner at 3/6/9/12 O'Clock. Run the tool. Then put in the other 4 and do it again. You can do it in sets of 2 also. Unless yours is wildly different than mine, which is possible. Kraken Fan #69 Link to comment Share on other sites More sharing options...
ysrracer Posted May 22, 2019 Author Share Posted May 22, 2019 Ok I'm still confused. Regardless of how many rounds you put in, it still only loads them into the moon clip two at a time, right? That's why if you put in 8 rounds, you have to click it 4 times. Link to comment Share on other sites More sharing options...
KrakenFan69 Posted May 22, 2019 Share Posted May 22, 2019 Yes, but I did find it easier somehow. lol You may have just ruined it for me with logic. Kraken Fan #69 Link to comment Share on other sites More sharing options...
revoman Posted May 22, 2019 Share Posted May 22, 2019 If you don’t want to remove one of the little teats just put rounds in 1, 2, 3 and 4. Then you are putting 1 round in at a time. Then follow up with 5, 6, 7 and 8. A lot easier to remove one teat. Link to comment Share on other sites More sharing options...
ysrracer Posted May 24, 2019 Author Share Posted May 24, 2019 On 5/22/2019 at 4:15 PM, revoman said: If you don’t want to remove one of the little teats just put rounds in 1, 2, 3 and 4. Then you are putting 1 round in at a time. Then follow up with 5, 6, 7 and 8. A lot easier to remove one teat. Ok, I ordered one tonight. I'll let you know how it goes. Link to comment Share on other sites More sharing options...
Brian B Posted May 31, 2019 Share Posted May 31, 2019 BMT Moon Loaders are the best for me. I have them for my S&W 610, 929, 627 and for my Ruger Redhawk 45Colt/ACP. They have saved me hours of work and torn skin.CheersSent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Daniele Posted June 1, 2019 Share Posted June 1, 2019 one on Ebay for just 45$!! Too bad he doesn't ship to Italy Link to comment Share on other sites More sharing options...
ysrracer Posted June 1, 2019 Author Share Posted June 1, 2019 3 hours ago, Daniele said: one on Ebay for just 45$!! Too bad he doesn't ship to Italy Damn it. I literally just got mine from BMT at twice the price. For me it's basically unusable for 8 rounds of Remington .38 special with TK .025 clips. There's just no way I can turn the metal part with my hand. It's too stiff. If I load 4 rounds ( thereby loading 1 round at a time, as opposed to loading 8 rounds, and loading 2 rounds at a time) I can turn it. I need to figure out a way to get more leverage. Maybe a handle of some kind? Link to comment Share on other sites More sharing options...
ysrracer Posted June 1, 2019 Author Share Posted June 1, 2019 On 5/22/2019 at 4:15 PM, revoman said: If you don’t want to remove one of the little teats just put rounds in 1, 2, 3 and 4. Then you are putting 1 round in at a time. Then follow up with 5, 6, 7 and 8. A lot easier to remove one teat. The only way for me to remove one of the teats is with an end mill. Mine aren't removable. Link to comment Share on other sites More sharing options...
PatJones Posted June 1, 2019 Share Posted June 1, 2019 Damn it. I literally just got mine from BMT at twice the price. For me it's basically unusable for 8 rounds of Remington .38 special with TK .025 clips. There's just no way I can turn the metal part with my hand. It's too stiff. If I load 4 rounds ( thereby loading 1 round at a time, as opposed to loading 8 rounds, and loading 2 rounds at a time) I can turn it. I need to figure out a way to get more leverage. Maybe a handle of some kind? It's pretty tight, but doable, for me with Remington brass and the blued TK clips. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now