Will_M Posted July 13, 2014 Share Posted July 13, 2014 (edited) I'm loading for an AR15. Brass has been trimmed to 1.750". 55gr FMJBT bullet. 2.235" OAL. Stag 3G barrel, Bravo Company Mfg BCG, Palmetto upper receiver. Loaded rounds keep getting stuck in the chamber and require mortaring the rifle to get the loaded round out. All rounds extracted have a similar helical drag mark on the bullet. It's most visible on the round on the left. All rounds pass the case gauge easily. Any ideas why my reloads keep getting stuck in the chamber? Edited July 13, 2014 by Will_M Link to comment Share on other sites More sharing options...
PKT1106 Posted July 13, 2014 Share Posted July 13, 2014 (edited) Make sure the shoulder is properly re-sized. You have to "cam-over" the press arm to make sure the brass gets all the way up into the die. Are you full length sizing or neck sizing? For semi auto rifles, it is recommended to full length size every time. Edited July 13, 2014 by PKT1106 Link to comment Share on other sites More sharing options...
Will_M Posted July 13, 2014 Author Share Posted July 13, 2014 Make sure the shoulder is properly re-sized. You have to "cam-over" the press arm to make sure the brass gets all the way up into the die. Are you full length sizing or neck sizing? For semi auto rifles, it is recommended to full length size every time. Full length sizing. Die is adjusted according to Dillon instructions. I'm concerned about the consistent scratches on the bullet. Is that normal? Link to comment Share on other sites More sharing options...
slowhand23 Posted July 13, 2014 Share Posted July 13, 2014 Make sure the shoulder is properly re-sized. You have to "cam-over" the press arm to make sure the brass gets all the way up into the die. Are you full length sizing or neck sizing? For semi auto rifles, it is recommended to full length size every time. Full length sizing. Die is adjusted according to Dillon instructions. I'm concerned about the consistent scratches on the bullet. Is that normal? I had the same issue with a JP and Dillon 550 until I screwed the sizing die down further to the cam over position as mentioned. Good luck! Link to comment Share on other sites More sharing options...
Religious Shooter Posted July 13, 2014 Share Posted July 13, 2014 Scratches are normal. Usually from the sharp feed ramp. I'd bet you aren't setting back the shoulder far enough. Get a Hornady (uses your own caplipers) or RCBS mic and measure brass fired from your gun. Set your dies to set the shoulders back an average of .003". http://www.midwayusa.com/product/479704/hornady-lock-n-load-headspace-gage-5-bushing-set-with-comparator?cm_vc=ProductFinding Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 13, 2014 Share Posted July 13, 2014 I bought some .223 ammo from a reloader - had a tough time occasionally getting the loaded round out of the chamber. The reloader thinks it's because the bullet is not seated perfectly straight ... Link to comment Share on other sites More sharing options...
RiggerJJ Posted July 13, 2014 Share Posted July 13, 2014 screw the sizing die down to touching, then further 1/4 turn. I will wager the problem goes away... jj Link to comment Share on other sites More sharing options...
Dan Sierpina Posted July 13, 2014 Share Posted July 13, 2014 The case on the left shows a shiny line at the body/shoulder junction. The sizing die needs to be down more. I've had to take material off of the bottom of sizing dies in order for cases to fit in chambers that will take a Go gage properly. Link to comment Share on other sites More sharing options...
Nickoli Posted July 19, 2014 Share Posted July 19, 2014 Make sure the shoulder is properly re-sized. You have to "cam-over" the press arm to make sure the brass gets all the way up into the die. Are you full length sizing or neck sizing? For semi auto rifles, it is recommended to full length size every time. Full length sizing. Die is adjusted according to Dillon instructions. I'm concerned about the consistent scratches on the bullet. Is that normal? Don't follow Dillon's instructions for this one. I did, and had the same exact problem as you on my 550. If you look at the shoulder of your rounds, see how it has a radius on it? It should be a very "sharp", if you will, line around the neck. I took my Lee dies and threaded them in until they touched the shell plate. Lowered the plate and threaded the die in another 1/4 turn. Re-sized 1 dummy round, chambered, and it came out like butter. Link to comment Share on other sites More sharing options...
reptoid Posted July 19, 2014 Share Posted July 19, 2014 Scratches are normal. Usually from the sharp feed ramp. I'd bet you aren't setting back the shoulder far enough. Get a Hornady (uses your own caplipers) or RCBS mic and measure brass fired from your gun. Set your dies to set the shoulders back an average of .003". http://www.midwayusa.com/product/479704/hornady-lock-n-load-headspace-gage-5-bushing-set-with-comparator?cm_vc=ProductFinding What he said X 2 Link to comment Share on other sites More sharing options...
Collateral Posted July 20, 2014 Share Posted July 20, 2014 (edited) Here is easy way to sort out if it is ammo vs the gun. Try to separate the upper & lower then pull the BCG out. Insert a loaded round by hand into the chamber. If it feels like it is sticking stop, don't force it in farther. It should not stick and should fall right back out. If it sticks you can easily remove it with a cleaning rod inserted in the muzzle end, and it will easily tap it back out. The cleaning rod technique seems to clear a stuck round much easier than mortaring if you have one available and is less severe on your optic. If it sticks, try the same test with some factory ammo. If only the reloads stick take a close look at sizing process. It could be shoulder set back as others mentioned or bullet run out. The scratches look like they are from the feed ramps and are likely not contributing to the issue. Edited July 20, 2014 by Collateral Link to comment Share on other sites More sharing options...
bluevic443 Posted July 22, 2014 Share Posted July 22, 2014 Same issue. Had .005" taken off the base of the die. Now i can get the brass below the max on the Dillon case gauge. Do not like the idea of "cam over". Link to comment Share on other sites More sharing options...
drewbeck Posted July 22, 2014 Share Posted July 22, 2014 I've had the same issue before with cam over and just needing a little more bump back on the shoulder of the case. Your chamber may be on the tight side and it's amazing how leaving them just a little long gets them stuck like you were doing it on purpose! Go just a little shorter until they feed and eject from that chamber Link to comment Share on other sites More sharing options...
mgrs Posted July 23, 2014 Share Posted July 23, 2014 I also had to go cam over with my dillon size/trim die to get it to pass a wilson gauge. I was worried I was setting the shoulder back too far, but have not noticed decreased brass life. Link to comment Share on other sites More sharing options...
Doc Hunter Posted July 26, 2014 Share Posted July 26, 2014 Get the right tools to read and set up your die - Sinclair Int. is your friend. Also, the book "Reloading for Competition" will put you light years ahead of the curve. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now