buss544

Seriously??? Still didn't answer the question. Sent from my SM-G975U using Tapatalk

Question about price comparison between STI vs a custom gun and what is included. Does a custom gun include 3 magazines? I see that the DVC-O includes 1-170 and 2-140 which gets you in the game to play ball... even if it is a short life expectancy of the DVC Sent from my SM-G975U using Tapatalk

Love it. I drilled a detent hole in it so it wouldn't lock the slide back in recoil and added some grip tape on the pad.

Check out fortiusarms.com. That finish is one of his standard packages for an M&P

9/16 32 TPI is the thread pitch of the SJC and Carver Comps.

I needed to drill mine. I drilled it so deep I can't use it to lock the slide back. I need to take off my thumb safety to take the gun apart

Carver Custom BB-enterprise dot biz I have the Carver 3 port

If your barrel is a Kkm then I would be willing to trade you my minor 3 port Carver comp for your SJC. Send me a pm if you're interested.

Ya know the rule about only changing one thing at a time? I have a traditional SJC cmore mount and had ejection issues. I added the extended Carver ejector and increased my load to shoot major. I realized it was my load cause I took the compensator off and it ejected reliably. I can't say if the 90 mount holes will fit the traditional mount holes but I know the mini red dot mount holes line up perfectly.

There can be problems even if they do fit in the chamber. Mine would fit in the chamber but when I would unload and show clear the bullet would stay and the case would come out.

In regards to the installation of the thumb rest, is this a permanent modification where there are holes drilled into the frame or do they us the existing trigger pins?

I use this with the Rx inserts. I have clear, dark grey, copper and yellow. I just change out the lenses depending on the conditions

You can get 'switched' to open with an illegal modification

I only use the standard slide stop because of this reason

True. I don't use that recipe anymore.

They would stick in the chamber when I would unload, show clear. I was shooting an open glock with a Kkm barrel and loading as long as I could

This really isn't quite true, while it may help sell a lot of race holsters the time difference is not as significant as you'd think...plus race holsters are allowed in all divisions in IPSC and the Limited divisions of USPSA. I've put all my guns and holsters on the clock and I can draw my Glock out of a 6004 duty holster within a tenth of a second of what I can draw my race gun. On point 2 its the target focus used for every shot that makes the dot guns faster and the difference increases with distance/difficulty of shot. At 5m the time between any of the divisions is going to be minimal. At 25m its going to be significant. I tend to agree. since I shoot IPSC production we can use race holsters or duty holsters. the difference between drawing from a bladetech duty type bucket holster or a DAA race master or H&S CW5 is pretty insignificant. I prefer the race holsters but mainly because they give less holster wear on the gun than because I can draw any faster from it. The difference for me is that my open gun will not fit into a traditional holster.

MG are by far the best competition bullet. Check out xtreme bullets. They are cheap enough to use as range fodder

The breech faces are different. You will need a new slide. Sent from my SCH-I545 using Tapatalk

+1 Plenty of HP in stock but i cant use them over the winter when we shoot indoors

How long ago did you see them in stock. I've been checking 5-6 times a day and i can say that it has been about 3 months since I've seen them in stock

I cannot remember the last time I've seen these in stock. When was the last time you've purchased some? Do they only post 1 case at a time and I'm missing out?

http:// www. erietvnews. com/story /22600927/ shooting-championship-puts-spotlight-on-safety

The breechface is going to be too large for the 40...even with a new extractor. You'll need a new slide and you'll need to reload your 40 ammo long in order to get the ammo to feed

Check out fusion Firearms