redmercury2

HE feeds his cows used husks ?

The ice was way too big for me,forced my hand into a cramped position,i like the STI model way better.

May he burn in HELL !!!!

Bladetech makes a DOH model holster for that setup.

SAFARILAND # 771 ON A CR SPEED BELT,

We are honored to have you as part of our nation.

RED mount to c-more, superglue screws into frame,then run a line of liquid metal along the joint of the bottom of scope mount and dust cover. this holds with the heat of repeated bill drills in 110 degree az. summers, the loctite only method loosens in the heat.

Miculek comp with a JP ADJUSTABLE GAS BLOCK is the shi.. in my rifle

Pete, I have an old 1100, and an old Winchester Super X Model 1. I use the Winchester over the Remington. However, if I were in your position (needing a shotgun) I echo Kurt, get the Benelli over the Remington. Remington internals have always been stamped parts, very cost effective, but they can break. They don't very often, but, they will always bite you in a match. The other options, Browning or Winchester, current models are good too. By the way, I've seen videos of Kurt with his Benelli....with speedloaders, I couldn't load a Remington as fast as he loads that darn Benelli!!!! Pete, I have an old 1100, and an old Winchester Super X Model 1. I use the Winchester over the Remington. However, if I were in your position (needing a shotgun) I echo Kurt, get the Benelli over the Remington. Remington internals have always been stamped parts, very cost effective, but they can break. They don't very often, but, they will always bite you in a match. The other options, Browning or Winchester, current models are good too. By the way, I've seen videos of Kurt with his Benelli....with speedloaders, I couldn't load a Remington as fast as he loads that darn Benelli!!!!

What is the accuracy of the barrel compared to new?

30,000 ROUNDS at least on my open blaster,only probs are related to my reloads or mag springs.

$2,39 IN MESA ,AZ

What are your complaints?

ALL the stock DILLON parts including dies have served me well for the 15 years ive loaded super on my 1050. Well o0over half a million rounds. SOME LIKE OTHER DIES FOR SIZING to take the bulge out of case bases shot in feed ramps cut excessively. DILLON DIES are the best IHOH, respectfully best wishes.

HOW many pistol classifiers require more than 20 rounds.? Classifiers are used to evaluate our skills are they not ,the original post concerned a 15-20 limit which clearly requires all divisions to reload at least once or twice.

MY REM 1100 COMP MASTER has fired all the target loads of rem,winchester,and federal icould get at wal-mart from the first round with zero function problems,this is the 100 rounds for 15.75 pricing. FWIW

USPSA limits pistol stage round count but rmains freestyle.,my apologies ,i meant stage round count in original post.

IS it or would it be a good idea to limit round counts to say 15-20 in 3 gun shotgun so as to control the reload aspect as opposed to shooting aspect?

MOBIL 1 15/50 for all firearms and all gas engines ,ars love iall year round in s. az

I believe the clerk should ask if its for handgun or long gun,if u answer handgun a permit is required.

i roll on a case lube pad with imperial sizing wax and have NO sizing problems.

GOT a Bedell 38 shorty, got a Matt McLearn38 shorty, definitely like MATTS shooter more, sweet trigger and tighter groups with TOTAL reliability, Matt is 1000% behind his work, best wishes, doug

XM193 GIVES ME 2 MOA out of my 1/7,1/8,1/9 twists sierra 1390 bullet on 4895 gives me consistent sub 1 moa these are ten shot goups at 100 yards wsr primers ww brass 20x scope off the bench -best wishes

My STARLINE 38 SUPERCOMP BRASS lasts at least 12-15 reloads before a case neck split or i just chuck it cause i cant read the markings on the case headstamp. The ditched 9mm brass is a prob on the range for those who shoot other cal ibres,as we have to sort through it to get our brass back.

3N38 gives me mega comp flash,vv350 does not ,no temp variation probs with 350 and 350 requires less weight= lower cost.