xcutter45 Posted April 21, 2019 Share Posted April 21, 2019 Have loaded for bullseye 35+ years and IPSC/USPSA .45 Major long ago as well...no issues...recently got a XDm 9mm 5.25 to shoot and am working on a minor level load for it...147 SNS coated round nose, 3.1 gr. Sport Pistol, Fed. 100 match (all I had on hand), 1.135" COAL, Winchester once fired brass...by all accounts that I can research, a sensible load...test fired 10 rounds today, 900 fps. avge. vel. (130 PF M.O.L.), very consistent & appears very accurate...question is primers are definitely flat...no signs of cratering, etc. and some slight radius to the outside edge remains but definitely flat...figuring this is somewhat normal for 9mm as it is a different animal and primer flatness is only one aspect of pressure but wondering what those knowledgeable could offer re the normality of this...BTW, just a very small touch of taper crimp as a final operation following seating...everything seems good to go sans the flattened primers...any thoughts appreciated...Thanks, Jerry Link to comment Share on other sites More sharing options...
AHI Posted April 21, 2019 Share Posted April 21, 2019 Have seen this Fed primers are very soft . If you need convincing try some Winchester small pistol primers. Link to comment Share on other sites More sharing options...
xcutter45 Posted April 21, 2019 Author Share Posted April 21, 2019 AHI, Thanks, yes I do know Fed. 100 GM`s are softer, that`s why I mentioned it...I suspected it might be a cause...I use them for BE & PPC revolver for that very reason...they are very reliable with lighter reduced hammer strikes in those target guns...I do plan on getting something else for the 9mm loads , likely WSP`s as you suggest...if that`s all it is, I`d be happy, as I think it`s a very good load otherwise...thanks for the response Link to comment Share on other sites More sharing options...
noylj Posted April 22, 2019 Share Posted April 22, 2019 I have found this ONLY with 9x19. If you start very low, you will find flattened primers. If you work the load up, the primers stop flattening and return to normal. If you exceed max, primers will again flattened, this time indicating pressure problems I have been called names and my technique insulted, but that is what I have seen. Only thought I have is the huge headspace gap with so many 9x19 cases being so short, that the primer actually gets pushed far out of the case with the low pressure not slamming the case head back against the breech as fast and the "reseating" of the primer when the pressure pushes the case head back flattens it. As I said, only seen it with 9x19. Work up your load, sort and use the longest cases, or ignore it. Also, I have found that accuracy really improves if I sort sized 9x19 cases. The longer cases give better accuracy than the short ones. Or, I use a L-SWC and use COL to shorten the head space gap, just like my .45s. If I had a real accurate 9x19, I would trim 9x21 cases to match that gun's headspace... Link to comment Share on other sites More sharing options...
xcutter45 Posted April 23, 2019 Author Share Posted April 23, 2019 noylj, Thanks for the thoughts...these are once fired Winchester white box cases...not sure how they would relate to others but will check some and see if they might be short... Link to comment Share on other sites More sharing options...
MemphisMechanic Posted April 23, 2019 Share Posted April 23, 2019 Federal primers are soft enough to show this within safe pressure ranges. Until you see this on a harder cupped CCCI/S&B/Win I wouldn’t give it the slightest thought. Link to comment Share on other sites More sharing options...
xcutter45 Posted April 23, 2019 Author Share Posted April 23, 2019 MM, Thanks a lot for the reply...truly what I was looking for feedback...going to try some Win. and I`m betting will be all good...9mm just a little different game, as I expected...Thanks to all that replied... Link to comment Share on other sites More sharing options...
Tawadc95 Posted May 1, 2019 Share Posted May 1, 2019 Noylj's experience is the same as mine. When I first started loading 9's I was quite baffled by my minimum powder trial load and a flat primer. Link to comment Share on other sites More sharing options...
Jim Watson Posted May 1, 2019 Share Posted May 1, 2019 Same deal. I once got nervous over a below maximum handbook load that severely flattened Federal primers. Back to WW or CCI, no flat. So I save the Federals for revolver loads. Link to comment Share on other sites More sharing options...
rustybayonet Posted May 7, 2019 Share Posted May 7, 2019 I call it good with the outside edge having a curve and no gas comming thru. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now