BiteTheBullet Posted February 1, 2019 Share Posted February 1, 2019 I am new to loading 38 short colt and was wondering if anyone has tried using Hodgen International or Clays in 38 short colt. If so what was the outcome? What grain charge? What grain bullet? I have some 160 gr Bayou bullets that I would like to load Link to comment Share on other sites More sharing options...
Mcfoto Posted February 1, 2019 Share Posted February 1, 2019 I’m only a couple months ahead of you so listen to more experienced folks who’ll be by shortly. I load 147 gr blues. Have been using up some Universal but had to push the max to make PF. Recently, I’ve gone to American Select and having good luck with that. 160 Bayou’s are very popular but I get the Blue Bullets for a little cheaper and don’t see any difference in performance. Link to comment Share on other sites More sharing options...
MikeBurgess Posted February 1, 2019 Share Posted February 1, 2019 I'm loading 147s with claydot (Clay's twin) loaded about 20k with it so far, it is super clean I dont even bring my cycluder brush any more and I'm going a few thousand between any cleaning at all.Sent from my SM-N960U using Tapatalk Link to comment Share on other sites More sharing options...
pskys2 Posted February 1, 2019 Share Posted February 1, 2019 (edited) Clays or Clay Dot are best in the 38 short colt used in an N Frame. Clean, makes PF easily and accurate. Only takes 2.8 with a 160 grain coated bullet, I use bayou's also, with an oal of 1.170". International is a bit slow for that case. Edited February 1, 2019 by pskys2 Link to comment Share on other sites More sharing options...
BiteTheBullet Posted February 1, 2019 Author Share Posted February 1, 2019 What power factor are you making with that load you are using? Link to comment Share on other sites More sharing options...
jcc7x7 Posted February 2, 2019 Share Posted February 2, 2019 (edited) 160 Bayou's , there the best. I use .358 in the 929 and 627 (obviously 9mm and 38 sc) 2.8-3.0 grains of Clays (clay Dot when clays is hard to find) One gun has a large cyl/bbl gap so wants 3.0grs to make PF Fed spp Starline 38 sc brass col 1.150 Pf 128-132 Edited February 2, 2019 by jcc7x7 Link to comment Share on other sites More sharing options...
MikeBurgess Posted February 2, 2019 Share Posted February 2, 2019 One thing to keep.in mind with revo loads in particular is you want to work up loads for your gun, my wife and I both have 627s and they run about 10pf different with the same ammo. Also with heavy bullets, small cases and fast powders OAL will have a huge affect on pressure. A friend just did a batch of 160s at a shorter than his usual OAL and the cases stuck and the primers were flatter than I've ever seen. So start low and work up with your gun bullet OAL combination and a chrono Sent from my SM-N960U using Tapatalk Link to comment Share on other sites More sharing options...
ysrracer Posted November 1, 2020 Share Posted November 1, 2020 Name: .38 Short Colt: 160gr Bayou RN: Clays 3.0gr: OAL 1.20 Notes: S&W 627 5" Shots: 8 Average: 759 ft/s SD: 20 ft/s Min: 726 ft/s Max: 791 ft/s Spread: 65 ft/s Power Factor Average: 121 Power Factor Low: 116 Power Factor High: 126 Barometric Pressure: 30 in Hg Temperature: 85 F Weight: 160.0 gr. Powder: Clays 3.0gr Bullet: Bayou 160gr RN C.O.A.L.: 1.20 Primer: Fed SPP Case: Starline Link to comment Share on other sites More sharing options...
Farmer Posted November 1, 2020 Share Posted November 1, 2020 FWIW International Clays does not play well in metallic loadings. It gets Very spikey and just doesn’t work well. There’s lots of better choices out there. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now