EkuJustice Posted October 21, 2013 Share Posted October 21, 2013 I was thinking 115 when I first saw the post. A heavier bullet with the powder charge of a much lighter bullet and a short oal is asking for trouble. You got lucky on that one Link to comment Share on other sites More sharing options...
Powder Finger Posted October 21, 2013 Share Posted October 21, 2013 I think you should seriously consider reading a loading manual and doing more research than "several people told me"... Well, the previous owner of the gun I used and the load data on this site said 9grs Anyway, now I have a load if USPSA changes major to 200 :) if you make it till then. Link to comment Share on other sites More sharing options...
Mat Price Posted October 24, 2013 Share Posted October 24, 2013 (edited) HS-6 Lot 2219 I use 9.3 grains with a 124. This is a very slow lot. Probably what happened the previous owner had that lot or told you to use a 115. New lot back to old burn rate. this is why i ALWAYS ALWAYS ALWAYS drop my charge and chrony when i open a new jug of powder. My chrony results where crazy with lot 2219... 8.4 grains = 155 pf or something. HOWEVER i wish hogdon would make this mistake again... call it hs6.5 I usually use 8.6 grains hs6 at 1.165 with a 124 jhp for 173-5 pf i suggest reading this thread http://www.brianenos.com/forums/index.php?showtopic=147730&hl=+mat%20+price Edited October 24, 2013 by Mat Price Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 so maybe I have a crazy lot then. So I've loaded some with 8 grains only and I'm still getting a PF of 180. This is again 124 CMJs, same OAL, with a shortie. very weird but I'm going to go down to 7.5grains. Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 Something isn't right. You need to double check your charge and chronograph Sent from my SAMSUNG-SGH-I317 using Tapatalk Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 But it's not that far off I get 175 with 1.65 you are getting 180 with 8 grains at 1.150 Sent from my SAMSUNG-SGH-I317 using Tapatalk Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 Oal of 1.165 not 1.65 Link to comment Share on other sites More sharing options...
gng4life Posted October 27, 2013 Share Posted October 27, 2013 Just like I posted before, I said you should have started around 7.5 and you would have been in a better position to work up. Let us know how it works out... Also, why don't you go out a little further, like 1.165-1.170? Thats the most common range for that bullet with that load with that platform. It's not just for pressure, it's also for feeding reliability. Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 Just like I posted before, I said you should have started around 7.5 and you would have been in a better position to work up. Let us know how it works out... Also, why don't you go out a little further, like 1.165-1.170? Thats the most common range for that bullet with that load with that platform. It's not just for pressure, it's also for feeding reliability. so that's a good question. Somehow I"m using this EGW chamber checker and anything longer than that won't fit. I just wanted to be on the safe side. How do you guys check that for longer loads? Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 In the bbl. Best chamber gauge made is the one you will be firing the round in. Drop the finished round in the chamber give a light tap with your finger if the round s falls out with no resistance and is in the chamber all the way when you turn the barrel over its good Sent from my SAMSUNG-SGH-I317 using Tapatalk Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 In the bbl. Best chamber gauge made is the one you will be firing the round in. Drop the finished round in the chamber give a light tap with your finger if the round s falls out with no resistance and is in the chamber all the way when you turn the barrel over its good Sent from my SAMSUNG-SGH-I317 using Tapatalk so for 38S I've never needed the barrel since the EGW works fine. I hate to just check round by round in the bbl. Any other ideas? Link to comment Share on other sites More sharing options...
atbarr Posted October 27, 2013 Share Posted October 27, 2013 I don't barrel check my practice rds., I barrel check everything else. Everything else. Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 I don't barrel check my practice rds., I barrel check everything else. Everything else. since I don't practice in the winter months, everything else is "everything" Link to comment Share on other sites More sharing options...
kneelingatlas Posted October 27, 2013 Share Posted October 27, 2013 Why would you feel more comfortable checking your rounds in a chamber gauge that in the actual chamber in which you plan to fire the rounds? By all means if you have an OAL which feeds reliably stitch to it; I'm just curious. Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 Why would you feel more comfortable checking your rounds in a chamber gauge that in the actual chamber in which you plan to fire the rounds? By all means if you have an OAL which feeds reliably stitch to it; I'm just curious. No I mean it's more hectic to check round by round. I have this 50rnd thing I got from a friend, it's kind of faster... Link to comment Share on other sites More sharing options...
lcs Posted October 27, 2013 Share Posted October 27, 2013 You measure the OAL. The OAL for using STI mags in 9 Major should be 1.165. You get minor variances in OAL with different headstamp brass. That barrel will run 1.165 with issue. Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 (edited) You measure the OAL. The OAL for using STI mags in 9 Major should be 1.165. You get minor variances in OAL with different headstamp brass. That barrel will run 1.165 with issue. so you're saying I"m loading too short and I should go longer? did you measure round by round in the bbl when you loaded? Edited October 27, 2013 by DrLove Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 I'm thinking you really need to read a reloading manual. Set your seating so that it seats the rounds at 1.165 after you Liam say 300 rounds remove your bbl and chamber check them Link to comment Share on other sites More sharing options...
DrLove Posted October 27, 2013 Author Share Posted October 27, 2013 I'm thinking you really need to read a reloading manual. Set your seating so that it seats the rounds at 1.165 after you Liam say 300 rounds remove your bbl and chamber check them so the problem now Matt is that no reloading manual will tell me how "this specific" gun will function. I kind of trust the "original owner" more on this (above) . Link to comment Share on other sites More sharing options...
Mat Price Posted October 27, 2013 Share Posted October 27, 2013 It's simple load the ammo as long as you can and still feed reliably. This gives you more room in the case for powder. Higher charge to make the same power factor at the same pressure is good. More gas to run the comp Sent from my SAMSUNG-SGH-I317 using Tapatalk Link to comment Share on other sites More sharing options...
Sarge Posted October 28, 2013 Share Posted October 28, 2013 DRLOVE, What I do is use my barrel when developing loads. I make sure they are not too long, drop in and out freely etc. Then start using your gauge. If a round fails the gauge then drop it in the barrel. If it goes you know that failed rounds can be used for practice since they likely will chamber OK. For awhile check all rounds that pass the gauge by dropping them in the barrel as well. What you want to ultimately prove is that anything that passes your gauge will pass the barrel test then you can quit using the barrel and just use the 50 round checker. You may have to glue some spacers under the 50 round gizmo to get it up off the table so your long 9MAJOR rounds will go all the way in without bottoming out. This is why I just use a single round gauge. I can hold it in my hand. Hope this made sense. Link to comment Share on other sites More sharing options...
DrLove Posted October 28, 2013 Author Share Posted October 28, 2013 DRLOVE, What I do is use my barrel when developing loads. I make sure they are not too long, drop in and out freely etc. Then start using your gauge. If a round fails the gauge then drop it in the barrel. If it goes you know that failed rounds can be used for practice since they likely will chamber OK. For awhile check all rounds that pass the gauge by dropping them in the barrel as well. What you want to ultimately prove is that anything that passes your gauge will pass the barrel test then you can quit using the barrel and just use the 50 round checker. You may have to glue some spacers under the 50 round gizmo to get it up off the table so your long 9MAJOR rounds will go all the way in without bottoming out. This is why I just use a single round gauge. I can hold it in my hand. Hope this made sense. Thanks Sarge, this is useful, I'll try it. Link to comment Share on other sites More sharing options...
spencerhut Posted November 18, 2013 Share Posted November 18, 2013 Are you tumbling loaded rounds? Are you running the chrono after a long hot match? Have you rechecked your OAL after racking them into your chamber a few times (checked for set-back)? What on earth does tumbling the rounds have to do with anything? I think you may have some bad info. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted November 18, 2013 Share Posted November 18, 2013 I don't think you can get a 124 to 1650 with 9 grains out of a shorty. I just did. The cases were pretty full with 9grs but I did weight the bullets, 124 it is. Anyway, I"ll reduce and chrono again. I don't think the chrono is an issue You are lucky you did not blow yourself up. I will go 115 at 8.5 and go from there. I think you just might be starting to understand what everyone here has told you very nicely, but I'm not positive, so let me start from scratch. Loading 9mm major is dangerous You can get hurt unless you follow the rules of loading 9mm major The rules are simple You NEVER just throw together a major load that you have heard will give you PF 170 or 175. You start at least 0.5 grains lower than you've confirmed and test that thru a chrono, and work uP. Slowly. And yes, you should try a little longer OAL if it fits thru your mags/chamber. 1.16 - 1.17 is a little safer, especially if you have a full case. Link to comment Share on other sites More sharing options...
Sarge Posted November 18, 2013 Share Posted November 18, 2013 Are you tumbling loaded rounds? Are you running the chrono after a long hot match? Have you rechecked your OAL after racking them into your chamber a few times (checked for set-back)? What on earth does tumbling the rounds have to do with anything? I think you may have some bad info. Some believe there is evidence that excessive tumbling can pulverize powder and change it's characteristics It's been talked about here in the past.. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now