Sandbagger123 Posted September 9, 2013 Share Posted September 9, 2013 had a match and the steel would not stay up. looked to be just a turn of the bolt to fix it. some wanted to do it themselves, which i have seen done before, but i insisted that the MD be called to do the adjusting. I got the feeling from some of the other shooter they did not like this as it took a little bit to get the MD there. I assume what i did was proper. Was it? Link to comment Share on other sites More sharing options...
JAFO Posted September 9, 2013 Share Posted September 9, 2013 (edited) Calling the MD shouldn't be necessary. The ROs should be adjusting the steel as needed throughout the match. If a shooter calls for a calibration, then call the MD (or designated calibration officer). Edited September 9, 2013 by JAFO Link to comment Share on other sites More sharing options...
motosapiens Posted September 9, 2013 Share Posted September 9, 2013 At local match we just adjust ourselves. It is not unusual for steel to pound itself into the dirt and need adjustment. Link to comment Share on other sites More sharing options...
Sandbagger123 Posted September 9, 2013 Author Share Posted September 9, 2013 Well now i feel bad doing so. i always thought stuff like this could only be adjusted by the MD Link to comment Share on other sites More sharing options...
High Lord Gomer Posted September 9, 2013 Share Posted September 9, 2013 (edited) The closest reference i could find for that, other than calibration, was 8.7.4: Altering stage props, targets or any other part of a COF without the approval of a Range Officer, or setting, resetting or activating moving targets on a COF identified as “Closed” or “Off Limits” will be subject to the provisions of Section 10.6. That implies that any RO has the ability to set or approve the setting of a target. When it comes to actually calibrating steel poppers, that is the job of the RM (frequently the same person at a local match). Edited September 9, 2013 by High Lord Gomer Link to comment Share on other sites More sharing options...
StealthyBlagga Posted September 9, 2013 Share Posted September 9, 2013 For a local match, the guy holding the clock is the RO and should be able to do the adjustments. Link to comment Share on other sites More sharing options...
aztecdriver Posted September 9, 2013 Share Posted September 9, 2013 For a local match, the guy holding the clock is the RO and should be able to do the adjustments. But if I put the clock down to use the wrench then I'm not an ro anymore. j/k. Thought it was just silly. Seriously, ROs are responsible for the target management and that include steel. If you wanted it calibrated following adjustment - that's an RM. call - but at most locals no one is running calibrated ammo. Don't feel bad. Tell them your leaning and now you know. Link to comment Share on other sites More sharing options...
Jim Norman Posted September 9, 2013 Share Posted September 9, 2013 A 'Competent Individual' should adjust the steel. In a local match the ROs are generally embedded. It is PROBABLY best that the MD/RM be called. It eliminates the arguments that occur later. In a LII or LIII match the adjusted steel really MUSt be calibrated. At a local match generally the calibratin knuckle is used. Is it really 100% right? No, to be 100% in compliance we should calibrate all steel with a calibratio gun that has been chronoed that morning. let us all be honest, this just ain't a gonna happen at a Local Match. So long as the steel is set at a reasonable level and maintained throughout the match this is all we can reasonably expect. Now, if a piece of steel or any prop or target needs to be corrected, the MD/RM needs to be notified. Oft times the persons in a squad are wonderful people, but the mechanical aspects of some targets are not their baliwick. Better to get he guy that knows than have multiple reshoots and then go get him. THe match flows better and the MD/RM isn't pissed off. Link to comment Share on other sites More sharing options...
EkuJustice Posted September 10, 2013 Share Posted September 10, 2013 At a local the squad just fixes it and goes on. Link to comment Share on other sites More sharing options...
gng4life Posted September 10, 2013 Share Posted September 10, 2013 Guys, as a MD, it's at least courtesy to let the MD do it or at least know about it. Remember, you are only one squad and there may be many more following behind you. If it's a recurrent problem, then the MD will know about it in the event it's faulty and needs new hardware or welding,etc. Besides that, if it's not set right, then you start having reshoots and complaints about steel and who does that go back to?? The MD. I'm not saying the MD is the only one that has to do it but you should have at least have told him so he can be aware of what is happening at his match. Link to comment Share on other sites More sharing options...
frankie Posted September 10, 2013 Share Posted September 10, 2013 at our local match we use the knuckle calibration but if repairs are needed the MD is at least to be notified Link to comment Share on other sites More sharing options...
Jim Norman Posted September 10, 2013 Share Posted September 10, 2013 Our local ruling is: If you have a REF you call the MD/RM to come see what happened. When this is followed there are rarely any major back-ups and the match flows. When this is not followed we have sadly had to throw out a stage as the repair was NOT done in a manner that maintained the presentation and presented a consistant shooting challenge. One reshoot due to REF is all we allow. After that call the MD/RM. Now if there is a problem, it is not your problem, it is owned by the MD/RM. If you odn't call him, you own the problem and if the stage is tossed or your squad gets a zero on a stage becasue you all shot it wrong because you fixed the stage wrong, it is YOUR fault. Same thing said two ways sort of. Link to comment Share on other sites More sharing options...
Flexmoney Posted October 1, 2013 Share Posted October 1, 2013 Ask YOUR Match Director for direction on how to handle it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now