roxfo Posted June 11, 2012 Share Posted June 11, 2012 HI all, I'm a new Super 1050 owner in the process of setting-up the press for .308 Win. I was hoping to use my Redding Comp Seater die (with 'sliding sleeve'), but on the upstroke, as the shell-plate starts to rotate, the bullet hits the sleeve (which has sprung out to its extended position). Has anyone else encountered this? Before I have the protruding part of the sleeve machined off, does anyone know of an alternative solution (or of any particular problems that would result from losing the bottom 1/2" off the sleeve)? The bullets are Sierra 2155, so not particularly 'pointy' (like VLDs), but they are seated to 0.020" off the lands, so are longer than SAAMI/factory OAL. Thanks for any advice! .. Link to comment Share on other sites More sharing options...
technetium-99m Posted June 11, 2012 Share Posted June 11, 2012 Not a 1050 user but on the LNL I just hold the bullet up in the die a bit and drop it down onto the case as it comes up into the die. A bit of a pain but it works okay. The 650 is cool to load on just for the shellplate coming straight up. Link to comment Share on other sites More sharing options...
DEP44 Posted October 19, 2012 Share Posted October 19, 2012 Same here. Exchanged the Redding comp for the Lee collet seater. Then the same thing with the Lee FC. The tip of the bullit (Prvi 145gr fmjbt) hits the sleeve, the whole cartridge tips but eventually makes it to the bin. Link to comment Share on other sites More sharing options...
hgr2 Posted October 19, 2012 Share Posted October 19, 2012 I tried using my Forster BR seater in my S1050 and had the same problem. I put the Dillon seating die in and everything was OK. Link to comment Share on other sites More sharing options...
pmclaine Posted October 20, 2012 Share Posted October 20, 2012 Timely post. Thank you OP. I'd like to set my S1050 up with a Forster seater for 30-06 and didnt consider this as an issue. If anyone has a solution and happily uses there Forster/Redding micrometer seater please post how you did it. Link to comment Share on other sites More sharing options...
RiggerJJ Posted October 20, 2012 Share Posted October 20, 2012 Unscrew the die until it doesn't hit the bullet on the upstroke, then reset. I use those dies on 223 & 308 on a 1050, works fine. JJ Link to comment Share on other sites More sharing options...
hgr2 Posted October 20, 2012 Share Posted October 20, 2012 I think you may loose the benefits that were designed into those spring loaded seating dies if you adjust the pre-stroke alignment out of them. Link to comment Share on other sites More sharing options...
DEP44 Posted October 20, 2012 Share Posted October 20, 2012 Thanks JJ, I'm going to give that a try. We'll see if it works for the Prvi's. I just compared them to Hornady 150gr fmjbt and it appears they are longer from the cannelure to the tip, so that may play a role as well. The Lee Factory Crimp die is still a no-go, but on trimmed cases the RCBS crimp works just as good. Even if I lose half of the spring function, I would still be able to switch projectiles just by adjusting the die to prerecorded numbers. Link to comment Share on other sites More sharing options...
RiggerJJ Posted October 20, 2012 Share Posted October 20, 2012 Thanks JJ, I'm going to give that a try. We'll see if it works for the Prvi's. I just compared them to Hornady 150gr fmjbt and it appears they are longer from the cannelure to the tip, so that may play a role as well. The Lee Factory Crimp die is still a no-go, but on trimmed cases the RCBS crimp works just as good. Even if I lose half of the spring function, I would still be able to switch projectiles just by adjusting the die to prerecorded numbers. Exactly. I value the preset or "dial a bullet" ability... jj Link to comment Share on other sites More sharing options...
wsl Posted October 21, 2012 Share Posted October 21, 2012 All, Here's how I solved this issue on my old-style 1050 to load .223. Should also work for the .308 on the new 1050. https://picasaweb.google.com/107754379149384581743/ReloadingPresses#5359435847628322626 Hope this helps, wsl Link to comment Share on other sites More sharing options...
Tom Freeman Posted October 21, 2012 Share Posted October 21, 2012 I just chopped off the bottom of the sleeve until it cleared. Link to comment Share on other sites More sharing options...
BullyDog Posted September 17, 2013 Share Posted September 17, 2013 All, Here's how I solved this issue on my old-style 1050 to load .223. Should also work for the .308 on the new 1050. https://picasaweb.google.com/107754379149384581743/ReloadingPresses#5359435847628322626 Hope this helps, wsl I have this same problem with redding competition seater on RL1050 What is the work around? Link to comment Share on other sites More sharing options...
roxfo Posted September 17, 2013 Author Share Posted September 17, 2013 (edited) What is the work around?I cut down the sleeve on a lathe, so it only-just protrudes below the bottom of the die when at rest. Has worked great ever since... Edited September 17, 2013 by roxfo Link to comment Share on other sites More sharing options...
Franco79 Posted September 18, 2013 Share Posted September 18, 2013 If you don't mind me asking why are you using a competition seater on a progressive press? I'm sure you would get a lot better consistency using it on a single stage press such as a Forster. Just my $.02 Link to comment Share on other sites More sharing options...
DougCarden Posted September 18, 2013 Share Posted September 18, 2013 Yep, what Tom said....Cut it off no problem.... DougC Link to comment Share on other sites More sharing options...
Tom Freeman Posted September 18, 2013 Share Posted September 18, 2013 If you don't mind me asking why are you using a competition seater on a progressive press? I'm sure you would get a lot better consistency using it on a single stage press such as a Forster. Just my $.02 I load all my bolt gun ammo (other than 50 BMG) on 550s. The quality of ammo coming out of them is as good as the ammo coming out of my old Co-Ax or Arbor press. Now days my Co-Ax is used to point bullets and gather dust. 338 Lapua is about as big as you can load on a 550. Had to cut off the bottom of the sleeve here also. Link to comment Share on other sites More sharing options...
roxfo Posted September 20, 2013 Author Share Posted September 20, 2013 If you don't mind me asking why are you using a competition seater on a progressive press? I'm sure you would get a lot better consistency using it on a single stage press such as a Forster. Just my $.02 I use a Redding comp seater because it makes very straight rounds, and the micrometer adjustment is very convenient. I use a progressive because I don't have 2 days a week to spend loading anymore - now I can make 200 rounds in the time I used to make 50 (still with precisely weighed charges though). My ammo is just as good as I used to make on a single stage - at least I've yet to find a measurable parameter that's worse or to see any worse results on target. But, I'm "only" a sling shooter, so I'm quite content with ½" groups at 300 yards or ½ minute at 1000. .. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now