HuntingPaper

Hello, I have and old CED7000 that has been working flawlessly and I decided to add a CEDgo light for practice in a crowded indoor range. The CEDgo works as intended by itself, had no problem pairing the TX and RX and the signal gets trigger when I press the test button. The problem comes when I plug the TX to the Aux output of the Timer, it sends one signal while plugging and seems to get stuck (shorted) while plugged. I’ve tried calling CED for support but after leaving some voice messages I had no response yet. Does anyone here has experience this problem? Thanks in advance for any advice.

Thank you!

Hello, Does anyone knows if this rig will be legal in IDPA CO according the 2022 revised rules? Thank you!

Hello! I’ll be in Virginia around the Harrisonburg area this Memorial weekend and I was wondering if there’s a local match in that area. I hope some locals are here and can point me in the right direction.

I let the springs loaded at max for over a week and it make no difference. I guess if you use + capacity pads it will relief pressure on the body. But if I have to invest on other parts to make them work correctly that makes them more expensive than ultra reliable factory mags. It is nice looking though... But looks only take you so far.

They wouldn't lock on my Glock 19 loaded to capacity on a closed slide and they didn't drop free from the swelling of the body. So it is are really a bad product

I bought a couple in 9mm 15 rounds (G19 magazine) to try them out on my JP GMR-13. They won't feed the 15 rounds without swelling and getting cought in the magwell also is impossible to get them to lock on a bolt closed. I give them a try loading them with 14 rounds and after shooting the last round the bolt hit the follower and took it out of the magazine. So, bottom line... This are absolute garbage and a waste of your money. Sent from my iPhone using Tapatalk

Thank you Pat Sent from my iPhone using Tapatalk

Hello. Does anybody uses a combination lije that? I would like to hear your experiences. Thank you! Sent from my iPhone using Tapatalk

I shoot only polymer guns in winter. My 1911 and CZ get so cold that is painful to hold them and like others say no grease on winter

Also keep in mind that Winchester 231 is very similar, some people claim is the same powder. In the Hogdon load data center shows the same loads for both powders. I've never used H38 but I have load W231 for 9mm, 40s&w and 45acp. I like it and is a great powder all around. The burning rate is similar to VV N320 Sent from my iPhone using Tapatalk 2

Any mods around? Can you please move this to the revolver section? Sent from my iPhone using Tapatalk 2

Thank you for the response. Any idea for a cilinder stop other than the original s&w part? Sent from my iPhone using Tapatalk 2

Yes. You can see on the unfired ones the hits on the rim and in one of those the hit is on the edge of the primer. They also look like light strikes.

I have a 625JM that has been hitting some primers off center. I don't know if it is me not letting reset properly since always happen in the second shot of a double tap. If I slow down and make sure the trigger fully resets always goes bang... Any advice would be appreciated.

I'm a certified RO and I've never seen a discount on the matches here in NJ. That doesn't bother me if the whole squad is working too reseting the stage but there's always a group of people that never do anything to help. I think those should be charged double

Can you share some recipes for n110?

I've been using CLP to clean and Slide Glide and Hoppes to lubricate but I just got some Froglube and I'm trying on one handgun. I'm not 100% sell on it but it does smell nice...

Congratulations!!! Enjoy the blaster

I just did a batch of this bullets with 4.9gr of Clays and 1.250 OAL and shot a few over the chrono with an average of 707fps 155pf. They don't make major and I won't feel comfortable putting more Clays on them but shoot very accurate with a nice snappy recoil. I think I like this for practice.

Can you share your recipe with Clays? How many grains and OAL... Thank you!!

If I can get a slot for SS in the waiting list I will definitely shoot both matches

I've notice the same thing shooting 45ACP Precision Bullets with W231 out of my STI Trojan but haven't found out the cause yet. I thought it was part of the molly coat.

I don't know if you like revolvers but I have a Ruger LCR that I like a lot. Is under $400 and chambered in 38spl or 357 Magnum if you want a little more edge, is super lite, ultra reliable and a very smooth trigger pull.

I think if USPSA grows it would generate better and more matches, not without growing pains for sure. I've seen how our local matches have grown in number of shooters and became longer to the point that MD had to impose capacity limits on them but I believe that if it keeps growing it can allow to do more matches and with more shooters it also will come more stage designers and builders. I try to bring people to the sport and I hope there's more like me and the OP