Aristotle Posted September 3, 2008 Share Posted September 3, 2008 I'm piecing together some parts for my Springfield 1911 9mm, particularly to facilitate a lower trigger pull weight with a more crisp trigger break. I was going to experiment with the EGW Ultimate trigger kit, and realized it will not come with a hammer strut. I have tried removing my stock HS before, and that was a bear, so I'd rather buy a new hammer strut and pin to attach to my new hammer, and I'm contemplating getting EGW Titanium Cap and Hammer Strut. I got a really nice trigger job from JPL on my Dan Wesson. I've been contemplating ordering two sets of Titanium parts to put in both my Springer and DW. Any "felt" improvements" on titanium parts, or is it all more just "conceptual improvements". I'm almost leaning towards just a Ed Brown Steel H Strut. Am I missing out on not going Ti? Link to comment Share on other sites More sharing options...
HSMITH Posted September 3, 2008 Share Posted September 3, 2008 The advantage of the parts you are asking about is not in the pull but in locktime, lighter parts move faster given the same force so the gun will fire sooner than one with heavier parts. I use the EGW Ti short cap and Ti strut in all of my guns. Link to comment Share on other sites More sharing options...
Aristotle Posted September 3, 2008 Author Share Posted September 3, 2008 The advantage of the parts you are asking about is not in the pull but in locktime, lighter parts move faster given the same force so the gun will fire sooner than one with heavier parts. I use the EGW Ti short cap and Ti strut in all of my guns. Thanks for the reply HSmith, I was hoping you would chime in. So let me get this straight. Lock time = the time between when the trigger is depressed, and when the firing pin strikes the primer? If you use them exclusively, then you have obviously found some profound advantage over steel parts, which is good enough for me. I'm going to give it a try. Link to comment Share on other sites More sharing options...
Matt Cheely Posted September 3, 2008 Share Posted September 3, 2008 The advantage of the parts you are asking about is not in the pull but in locktime, lighter parts move faster given the same force so the gun will fire sooner than one with heavier parts. I use the EGW Ti short cap and Ti strut in all of my guns. +1 Link to comment Share on other sites More sharing options...
HSMITH Posted September 3, 2008 Share Posted September 3, 2008 Yes, locktime is the time it takes from sear break to the firing pin to hitting the primer. I don't think I would call the difference profound, but I can tell the difference using the same load in the same gun. I like the absolute lightest fire control parts I can get and maintain consistent ignition. Link to comment Share on other sites More sharing options...
SLM Posted September 4, 2008 Share Posted September 4, 2008 Great, just great.... MORE parts I gotta buy!! Link to comment Share on other sites More sharing options...
SharonAnne9x23 Posted September 4, 2008 Share Posted September 4, 2008 i have the Cylinder and Slide Ti MS cap and Ti hammer strut in all of my 1911 fire control groups. Have had for about as long as they have been available. I have never regretted it. Link to comment Share on other sites More sharing options...
want2race Posted September 4, 2008 Share Posted September 4, 2008 I round the bottom of the strut and if the Ti cap has a long post, shorten it. The bottom of the strut doesn't fit very well into the cap as is from the package. Looks to be cut from flat stock. I like them and you can use them as is, but nothing is ever good enough "as is". Link to comment Share on other sites More sharing options...
mpeltier Posted September 7, 2008 Share Posted September 7, 2008 I round the bottom of the strut and if the Ti cap has a long post, shorten it. The bottom of the strut doesn't fit very well into the cap as is from the package. Looks to be cut from flat stock. I like them and you can use them as is, but nothing is ever good enough "as is". While your at it it is nice to polish the mating surfaces of thes two parts as well. Link to comment Share on other sites More sharing options...
davidwiz Posted September 9, 2008 Share Posted September 9, 2008 Also, if you have a Ti strut and cap, your gun should cycle differently, as there is less weight moving when the slide is in recoil. Link to comment Share on other sites More sharing options...
Joe D Posted September 10, 2008 Share Posted September 10, 2008 Total waste of time and money. We are not shooting a rifle off hand at distant targets. The only improvement you will notice is in your movement from one firing point to another - you will move faster as your wallet is lighter. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now