sasquatch981 Posted June 7, 2008 Share Posted June 7, 2008 (edited) So here is what I was thinking. Rather than dropping $500+ on a casepro, I thought I might blow $60 instead and see if it works. Here's my idea. Loading a Dillon 650 Station 1: Factory Dillon Sizer and decapper Station 2: EGW sizing die, with no primer punch pin Station 3: Powder Measure Station 4: Redding Competition Seating Die set to 1.200" Station 5: Lee Factory Crimp die. I realize that I have (3) dies that size the case, but since I shoot "glocked" range brass, and don't have 5 bills to spare on a casepro, any reason this would not work? Or am I just going at this with way too much gusto? Edited June 7, 2008 by sasquatch981 Link to comment Share on other sites More sharing options...
SLM Posted June 7, 2008 Share Posted June 7, 2008 That's about the set-up I run: Redding Ti resize/deprime Lee "U" die Powder drop Redding or Hornady Competition seater die Lee FCD I don't think it's overkill. The Redding is the tightest standard sizing die I've found and then followed up with the "U" die life is good. Yea, you could skip the standard size die and just use the "U" die if you wanted but I found that press runs a bit smoother and easier by doing the "two step" resizing. Link to comment Share on other sites More sharing options...
DougCarden Posted June 7, 2008 Share Posted June 7, 2008 Nah, that is the almost the same as mine , Dillon , then Lee regular .40 die (which for $12 resizes all the way down....) Regular Dillon seater and Lee FCD....My stuff all gauges, all the time.... DougC Link to comment Share on other sites More sharing options...
Singlestack Posted June 7, 2008 Share Posted June 7, 2008 EGW die in #1 is all you need. Use One Shot. Link to comment Share on other sites More sharing options...
HSMITH Posted June 7, 2008 Share Posted June 7, 2008 Skip the FCD and add a Case-Pro, that the set up I use. Link to comment Share on other sites More sharing options...
Flexmoney Posted June 10, 2008 Share Posted June 10, 2008 Loading a Dillon 650Station 1: Factory Dillon Sizer and decapper Station 2: EGW sizing die, with no primer punch pin Station 3: Powder Measure Station 4: Redding Competition Seating Die set to 1.200" Station 5: Lee Factory Crimp die. While I just use a Lee 4-die set (and it works great), your proposed setup would be ideal. Link to comment Share on other sites More sharing options...
UW Mitch Posted June 10, 2008 Share Posted June 10, 2008 I'm basically running the same set-up for 40 and 9. Works for me! ~Mitch Link to comment Share on other sites More sharing options...
Thomas Moore Posted June 10, 2008 Share Posted June 10, 2008 i'm running the same setup and i have a picture somewhere on this site. i believe it's under the heading case pro. i use the dillon die in station one because the bottom is flared more to accept 99.9% of the brass. the egw die has a narrow opening which may cause more cases to not line up correctly. Link to comment Share on other sites More sharing options...
edwin garcia Posted June 10, 2008 Share Posted June 10, 2008 Skip the FCD and add a Case-Pro, that the set up I use. +1 I love my Case Pro. I've tried the 2 'u' dies thing and still not comparable with a CasePro. $500+ but worth it if you're serious about your ammo. I load .38SC. Link to comment Share on other sites More sharing options...
unclebob Posted June 15, 2008 Share Posted June 15, 2008 Putting an ECW die in station 3 on a 650 well depend on what powder measure you have, the old style with the powder return strings, or the fail safe system. If you have the fail safe system you would have to modify it too use the return springs, The ECW die as far as I can tell resizes just as far down as the regular Lee sizer die. It just sizes the case .001 smaller in diameter. I did an experiment I sized 500 cases using the ECW on a Rock Chucker press then loaded them on a 650. Leaving the Dillon sizer die in place. I still had the same amount of rounds that would not gage check as I did with just using a standard Lee sizer die or a Dillon sizer die. IMHO all you are doing in using the ECW is overworking the brass, in turn sooner split cases. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now