Orion1 Posted December 13, 2022 Share Posted December 13, 2022 My Dillon 550B started giving me an issue after I changed dies. Changing the dies doesnt have a relationship with the issue at hand. All of a sudden, when I push the handle forward, the handle doesnt go as far as it normally doesn and the primer punch under the shell plate doesn't go up high enough. Without a case in station 1, I push on the handle like I am seating a primer and noted how high it goes: the punch goes high enough where it doesnt hit the primer feeding assembly and allows a very small amount of room for the primer to fall into the primer cup. If I increase the length of the primer punch, it will not load a primer from the primer feeding assembly. If I decrease the length of the primer punch, it will not active the primer feed stop pin that drops the primer. I tightened the roller bracket screws as per Gary's instructions here, however the handle primer punch under the shell plate isnt going up as high. Any insight would be appreciated. Link to comment Share on other sites More sharing options...
HesedTech Posted December 13, 2022 Share Posted December 13, 2022 (edited) 52 minutes ago, Orion1 said: All of a sudden, when I push the handle forward, the handle doesnt go as far as it normally doesn and the primer punch under the shell plate doesn't go up high enough. Did you check to see if there are any obstructions under the shell plate? If handle stops before reaching full forward something is in the way. Look and clean everything, including ram. Remember the shell plate is coming down and not the punch going up. Edited December 13, 2022 by HesedTech Link to comment Share on other sites More sharing options...
Orion1 Posted December 16, 2022 Author Share Posted December 16, 2022 (edited) On 12/13/2022 at 4:17 PM, HesedTech said: Did you check to see if there are any obstructions under the shell plate? If handle stops before reaching full forward something is in the way. Look and clean everything, including ram. Remember the shell plate is coming down and not the punch going up. I did and there are no obstructions of the main shaft. I added 30w oil to the shaft and it seems to be getting harder to move it up and down. I've also disassembled the main shaft from the press and freely move it up and down without issues. Thinking the issue is the threaded link arm pin needs to be greased. Thoughts? Edited December 17, 2022 by Orion1 Link to comment Share on other sites More sharing options...
ddc Posted December 16, 2022 Share Posted December 16, 2022 check the linkage arms for cracks or breaks Link to comment Share on other sites More sharing options...
HesedTech Posted December 16, 2022 Share Posted December 16, 2022 3 hours ago, Orion1 said: I've also disassembled the main shaft from the press and freely move it up and down without issues. Thinking Then your issues must to be in the arms and pins. Without any dies or brass the ram should fully move up and down. It should the arm should smoothly over center at the top of the stroke and fully compress primer punch cup when bottomed and pushed forward. The 550C has grease fittings, but removing the pins is no big deal, so grease em up. If all else fails send it to Dillon and they will refurbish the press for a fee. Link to comment Share on other sites More sharing options...
boatdoc173 Posted December 16, 2022 Share Posted December 16, 2022 I would do the following 1. take down and clean the primer assembly--be sure to clean the debris off the rim of the cup-- check for obstructions, debris.. that might hinder your priming system and 2. get a spent primer and c=double check that the primer cup assembly is seating it as primers should be on your machine( put a spent primer on a hard surface, cover it with t he primer cup,loosen the retaining screw below the cup, press the primer cup assemble onto a hard surface --all the way down =correct seating depth). tighten the retaining screw and retry you priming of cases BTW-- what kind of primers are those? they look strange finish wise Link to comment Share on other sites More sharing options...
dillon Posted December 16, 2022 Share Posted December 16, 2022 When you push forward on the handle to seat the primer, does the platform spring up when you remove your hand from the handle? If not, then the pivot pins are dry and require regreasing. Push down on the edge of the shellplate between stations 2 and 3. If it feels springy, then the shellplate bolt needs to be tighter. Make sure that the number stamped on the shellplate for identification is on the top of the plate. It can be installed upside-down. Be sure the handle isn't contacting anything when you push forward on the handle. Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 ok, this pin will not come out. I've taken a hammer and thick punch to it. This pin will not come out. Do I take it to a chop shop or toss this press out? I'm out of ideas. Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 (edited) 22 hours ago, dillon said: When you push forward on the handle to seat the primer, does the platform spring up when you remove your hand from the handle? If not, then the pivot pins are dry and require regreasing. Push down on the edge of the shellplate between stations 2 and 3. If it feels springy, then the shellplate bolt needs to be tighter. Make sure that the number stamped on the shellplate for identification is on the top of the plate. It can be installed upside-down. Be sure the handle isn't contacting anything when you push forward on the handle. That's correct, the threaded link arm pin needs grease. However, the pin will not come out. I just posted pictures above this message. What machine will remove these threaded link arm pins out, I've put all I got into it with a punch and hammer and it won't move more than what is pictured. Any help would be appreciated. I just got in 4,500 45 ACP bullets and was looking forward to reloading during my two weeks off! Edited December 17, 2022 by Orion1 Link to comment Share on other sites More sharing options...
HesedTech Posted December 17, 2022 Share Posted December 17, 2022 38 minutes ago, Orion1 said: However, the pin will not come out I have a 550C and the upper pins, per instructions, are held in on the arm. You pictures look like you have the arms off already. look at this for help. https://www.dillonprecision.com/s000244-61 Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 29 minutes ago, HesedTech said: I have a 550C and the upper pins, per instructions, are held in on the arm. You pictures look like you have the arms off already. look at this for help. https://www.dillonprecision.com/s000244-61 Youre correct, I'm referring to the threaded link arm pins then. Sorry for the confusion. Link to comment Share on other sites More sharing options...
RudyVey Posted December 17, 2022 Share Posted December 17, 2022 2 hours ago, Orion1 said: That's correct, the threaded link arm pin needs grease. However, the pin will not come out. I just posted pictures above this message. What machine will remove these threaded link arm pins out, I've put all I got into it with a punch and hammer and it won't move more than what is pictured. Any help would be appreciated. I just got in 4,500 45 ACP bullets and was looking forward to reloading during my two weeks off! There two small holes in front of the top of the link arms. You can see these holes on the schematic that was posted. This is where you have to put some grease i from time to time. I use an old syringe with a large diameter needle. Works great. I do not think you are supposed to take the pin out for applying lubrication. Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 11 minutes ago, RudyVey said: There two small holes in front of the top of the link arms. You can see these holes on the schematic that was posted. This is where you have to put some grease i from time to time. I use an old syringe with a large diameter needle. Works great. I do not think you are supposed to take the pin out for applying lubrication. 62286 are the pins I am trying to remove. Dillon has a video on disassembly where these pins are removed. I would just use the syringe as you describe, but I think 20 years of debris/grease has been sitting on these pins and Id like to wipe 62286 clean. Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 Dillon is calling it the upper link arm pin also. Link to comment Share on other sites More sharing options...
Orion1 Posted December 17, 2022 Author Share Posted December 17, 2022 (edited) I soaked the pin in WD40 over night, sprayed more into this morning. After hitting a punch with a hammer through the solid left pin, I've been able to move that pin about 1/4". Any suggestions? Edited December 17, 2022 by Orion1 Link to comment Share on other sites More sharing options...
HesedTech Posted December 17, 2022 Share Posted December 17, 2022 The B model pins are pressed in, so if you have access to a hydraulic press they should come out easily. If not gently warm the outer frame with a heat gun, but be careful not to burn or melt the finish. I’ve worked with machines with similar construction over the years and a hydraulic press is often the best tool. Just be careful not to crack the frame. I believe it is cast and then machined which means it may break before it bends . If you have a hyd. press make sure the frame is properly supported before applying pressure. It looks like you are close to clearing the knurled end. Link to comment Share on other sites More sharing options...
Orion1 Posted December 18, 2022 Author Share Posted December 18, 2022 Hammering, hammering, hammering: Link to comment Share on other sites More sharing options...
dillon Posted December 19, 2022 Share Posted December 19, 2022 The knurling is what prevents the pins from walking out. You undoubtedly have some galling from the link arms deposited onto the pivot pins. Squirt some penetrating oil through the lube hole in the upper part of the link arm, and continue the beating (on the pin) until morale improves. The hard part is done. Link to comment Share on other sites More sharing options...
ysrracer Posted December 30, 2022 Share Posted December 30, 2022 Squirt some earl on it, heat it, beat the s#!t out of it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now