hump Posted November 29, 2015 Share Posted November 29, 2015 My extractor decided to give up today and I wanted to see if anyone had experience with the WC bullet proof extractor. I readjusted mine after the match and ran 3 mags without a failure but I still don't trust it. Link to comment Share on other sites More sharing options...
Ming the Merciless Posted November 29, 2015 Share Posted November 29, 2015 I run Wilson Bulletproof extractors in several of my guns with very good reliability. They still need the usual polishing and fitting, but all of mine have lasted many, many thousands of rounds. Link to comment Share on other sites More sharing options...
RPM8shot Posted November 30, 2015 Share Posted November 30, 2015 When I chipped the factory extractor at 45K rounds on my Para L1445 (My fault) I used the Wilson Bulletproof replacement. I have had it in the pistol for 40K plus rounds and no problems. On the occasion that I do need to adjust it I had to get that Tool From Brownells to bend it as it is F/N hard. Probably why it lasts so long. No need to worry about the Wilson part. It is great quality. Randy USPSA TY27966 ICORE CA8491 NRA LIFE MEMBER CVD5294 Link to comment Share on other sites More sharing options...
Dirty Rod Posted November 30, 2015 Share Posted November 30, 2015 I've used Wilson BP extractors for years. Good stuff. Link to comment Share on other sites More sharing options...
JonKC Posted November 30, 2015 Share Posted November 30, 2015 I have 4 pistols with Wilson BP extractors and have never had an issue. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
GunBugBit Posted November 30, 2015 Share Posted November 30, 2015 The Wilson will probably serve you fine and I haven't compared, but you might want to give the EGW Heavy Duty extractor a look. Link to comment Share on other sites More sharing options...
762rocstarr Posted December 1, 2015 Share Posted December 1, 2015 I have WC bulletproofs in 3 different guns. Haven't broken one yet. Link to comment Share on other sites More sharing options...
Chutist Posted December 8, 2015 Share Posted December 8, 2015 After reading this: http://www.brazoscustom.com/magart/ejection%20perfection.htm I think I'd go AFTEC if I was replacing it myself. Link to comment Share on other sites More sharing options...
Hany Posted December 8, 2015 Share Posted December 8, 2015 When I replace an extractor in a .45 acp, I just put in a Wilson BP. so far they have all been great. Im sure others are good too, but I have only used the WC BP in recent years. Link to comment Share on other sites More sharing options...
motosapiens Posted December 9, 2015 Share Posted December 9, 2015 i went to a wilson on my sti 9mm on the recommendation of a local gunsmith. it was easy to fit, and it made the extraction much more reliable. with less bend on the extractor, it provided significantly more tension on the case (but not too much). I'm very happy with it so far. Link to comment Share on other sites More sharing options...
DaveFromAus Posted December 10, 2015 Share Posted December 10, 2015 i went to a wilson on my sti 9mm on the recommendation of a local gunsmith. it was easy to fit, and it made the extraction much more reliable. with less bend on the extractor, it provided significantly more tension on the case (but not too much). I'm very happy with it so far. Did you have to blend any of the edges etc or did it run fine as drop in? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now