Jump to content
Brian Enos's Forums... Maku mozo!

Eagle4

Classified
 View Profile  See their activity

  • Posts

    101

  • Joined

  • Last visited

 Content Type 

Everything posted by Eagle4

  1. Eagle4
    Benelli M2 or Beretta 1301 you have a very good shotgun. M2 is more friendly to start quadload but you can perform with the Beretta. The new M2 Speed is ready to race ou Tof the box but i don’t know if you can have it in US. In second hand the M2 SP is a very good choice.
  2. Eagle4
    Damn i missed it....
  3. Eagle4
    Have you the problem with a fully loaded magazine ?
  4. Eagle4
    I have shoot in Russia, Bryansk range : sand is everywhere. Only open guys (with sand in the mags) and some manuals have trouble.
  5. Eagle4
    I have run both. Both are great choice. My feelings : more recoil with m2 than 1301 easier to load faster with m2 than 1301 more tuning parts available for m2 M2 fits better for tall people (1.80m and taller) if you don’t like clean your gun : m2 is your gun 1301 is ipsc world champion, m2 is #2, #3, #4 and #5 for 1301 again.
  6. Eagle4
    When you’re shooting practical did you need this part?
  7. Eagle4
    Not touch the cutout but polish the head to improve a little the loading.
  8. Eagle4
    Not enough strong but can make some issues happen. Since october i’m working on several kind of prototype springs, but actually the best results are with both stronger springs to have proper timing.
  9. Eagle4
    OEM lifter's main spring is too weak with a bended magic lifter's spring by adding an additional counter tension. It's timing problem unless you always have this issue in the past.
  10. Eagle4
    Hi ! your malfunction picture is usually from a too weak lifter's main spring for the bended liftier's spring (bad timing in fact). But after trying this too after 2000 / 2500 rounds : same suck. The challenge is to find the ring tension for keepig reliability in the time AND can fit the little space vailable in the trigger group.
  11. Eagle4
    CAS have you tried to bend the spring ?
  12. Eagle4
    Yes, you need a stronger or just a little longer spring to increase preload for the last shell.
  13. Eagle4
    Telecopic tube Pinyo Wizard.
  14. Eagle4
    Who have tried to bend the spring ?
  15. Eagle4
    You can buy this lifter or the complete trigger group directly to Beretta (in EU it's possible).
  16. Eagle4
    Ok, in shotgun ipsc match minimum one option 3 start each 12 stages.
  17. Eagle4
    My way to make a smooth option 3 table start not cocked hammer : Grab the gun and open the bolt, flip the gun, grab ammo, close the bolt with the ammo and load, trigger trick, rack and bang. And for Toni : i think the trigger trick is more smooth and fast than pushing the button.
  18. Eagle4
    I have tried the dril this afternoon, i don't have rack so i have used 4 ipsc plate and 2 popper beetween 11m to 13m with full choke. 1st attempt : 6.31sec / 2nd attempt 6.30 with one miss / 3rd attempt 5.77 sec and 4th attempt 5.58.
  19. Eagle4
    I think the bending solution can proove the spring is too weak and need a bigger coil to work properly.
  20. Eagle4
    Shoot 2, load 8 and shoot 4 ? I think under 6 is possible. i will try next time at the range. Thanks for the drill !
  21. Eagle4
    Very painfull to install after bending but prevent some loading issues.
  22. Eagle4
    Direct plug'n'play on factory tube.
  23. Eagle4
    No "decocked" start in ipsc shotgun. In decocked start i will certainly rack the bolt, activate the bolt release and start loading like i usually do.
  24. Eagle4
    On the FB page of Josh Kenny you will find an old vidéo of a table start, option 3, load 4, trigger pull,rack and shooting 4 plates un less than 3,2 seconds.
  25. Eagle4
    In ipsc the faster way : bolt closed , grab the gun (right hand), load 8 shell gun upside down with left hand, press the trigger with the right finger gun still upside down, rack gun still upside down and shouldering for fire.
×
×
  • Create New...