MCFooter

I have a SRM, 9 round mag tube on a 21” Benelli M2. On occasion the next to last and sometimes the last round will not get pushed onto the lifter far enough to be lifted. I have replaced the spring with one from Beven Gram and have the maximum spring length to still get the 9 rounds in the tube. Q: Is this a problem with the 9 round SRM tube since it is shorter than other 9 round (DMW) tubes? Q: Should I make this a 8 round tube with a longer spring or longer cap/plug? Q: Does / Can the step at the factory joint inside the mag tube cause this problem? I hope this is not considered a Proprietary question I see that Nordic has a nice new tube out but I would like to make what I have work if possible. Thanks, Mike

The Brownells look like a fair deal but I just had a friend load up (minus powder and primer) a couple boxes of Gray Winchester AA Trap hulls and they work well. I did use some hot melt glue on the crimped ends to help hold in the shot. The gray helps me keep it straight from the green and red live rounds. YMMV

I will be there in less than a week. Looks like it's going to be a cold SOB though.

The experts will be along shortly but my research has led me to believe and purchase the M2 21" Field.

What's your location?

I got this email and said the same thing. I will be glad to come on another date if that's better for Berry or NTPS.

Anyone know any of these guys in Alabama? http://www.scssa.org/ Looks like they are putting together a pretty nice range. http://www.scssa.org/construction_&_maintenance.htm

If I only wanted/needed a connector I would go HERE They were $13 Shipped but it looks like they have gone up a bit.

YEP, that's what you asked for just not what I read Sorry. I have experienced the out of battery condition in practice several times but didn't know there was something that could be done to change it.

Take a look at this THREAD. There is more than one way to get there but the pictures and process posted by vtecrx does work and only takes a few minutes.

Benny, Is there no fear of dammaging the barrel with slugs and a Full choke? Would you say IM is the tightest of the Factory Chokes that should be used with slugs? Thanks

Ken, Sorry for the confusion but I'm just asking in case slugs are needed in the same stage as some tough take down steel. No plans to use slugs instead of buckshot.

As the Subject says I would like your opinion on the tightest choke that can be used in a Benelli M2 with Slugs. The reason for the question is I shoot a local “Outlaw” match that is notorious for having hard to take down steel. In fact most all the regulars uses Buckshot except me. I may need to start using buckshot but since it cost 4-5 times more I would prefer not to. Is there a problem using the factory “Full” Choke with Slugs?

I haven't seen the STI site but see if this is what you're looking for. http://www.sniperworld.com/glock/

The GSSF Prices are pretty good but if your not a member and have to pay sales tax depending on your location Topglock.com prices are about the same or better. Note: I have never purchased from Topglock.com

I think this is it. http://www.defensiveedge.net/

I would say it depends on where you plan to shoot. Mine will hold 9+1+1 but it's currently plugged due to the matches I shoot.

UNDER

I see Brownells has started selling the 6 round Stripper. Are there any plans for them to carry the 4 round Stripper?

Does anyone know if this match will require USPSA membership? I sent an email to Wayne a few days ago but haven't heard back yet. Thanks

I think I had to de-flash and polish a little on the inside of mine.

This one came on ebay today. Looks like it's Camo. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...=ADME:B:SS:US:1

Have you already asked The Benny Hill at http://www.triangleshootingsports.com ? Mark at http://www.murphyshotguns.com claims to be able to get Benelli barrels. He also post on Gunbroker under "a50caliber".

OK you guys are begging TWO Questions. 1) Where can you buy the Dan Young Carriers? (I can't seem to find them with a search) 2) How do they compare with the JP's on Quality, Price and Service? Thanks

Thanks, MyBoyElroy Two of the three Look the same is that the case or are there small differences between them?