mhop

YES BARRY, THERE WERE 6 THAT CAME IN, THE NEXT SHIPMENT IS EXPECTED IN DECEMBER CONTACT ME AND WE CAN ARRANGE BACKORDERING ONE THANKS

http://www.czforumsite.info/index.php?topic=29720.msg181195#msg181195 $3399 go to above like for inquires

CZ-USA Now is offering the Czechmate in 9mm http://www.czforumsi...81195#msg181195 for details of sale Czechmate comes with ambi slide racker c-more slide ride sight 6moa dot 2 spare serial matching threaded barrels 1 26 round magazine 3 20 round magazines mag loader aluminum grips aluminum magwell comp hammer 4 port comp barrel nut with removable front sight rear fixed sight 2 slide stops with finger groove 4 without finger grooves czechmate frame is different than TS grip is undercut, frame has notch for c-more mount, cleaning rod cleaning brush

i can tell you for a fact he gets complete shadow's and then does the work on them, on tuesday i will send in the paperwork to uspsa so this is resolved

EXACTLY ALL YOU HAVE TO DO IS SAY IT IS A SHADOW I HAD ANGUS WORK ON, NOW THEY HAVE TO PROVE THAT IT ISNT A SHADOW AND IT IS A SHADOW TARGET

how are they going to prove that you have a shadow target or a shadow that has had all the same work done to them like a shadow target

www.cz-usa.com

i have had no change in titegroup from 35 degrees to 100, in my sp-01 with 4.0 grains i get 130 pf i would go up .1 grain and call it good

why use a fisheye lense it makes your eyes strian

JT what are the ground conditions, i.e. gravel or grass bays thanks

B, it also says use your highest iron sight classification in the rule pages

is there going to be a sight in range/ function fire thanks matt

not a shooting vacation hum!!!!

i am going to be using mg 124 jhp in 9mm everybody says no longer than 1.100, i have 100 loaded up and shot and no problems the length was 1.125, another person was loading zero's in the same gun at 1.125 and no problem why does everybody say load so short have you each measured to check what length is the max or is everybody just going by what one person measured thanks matt

here are the totals from the self squadding page Limited GM 4 M 11 A 13 B 21 C 41 D 4 U 5 Lim 10 GM 0 M 2 A 4 B 10 C 11 D 5 U 2 Open GM 4 M 16 A 15 B 19 C 14 D 1 U 1 Prod GM 2 M 4 A 8 B 25 C 25 D 5 U 5 SS GM 0 M 0 A 4 B 15 C 11 D 3 U 5 Rev GM 1 M 1 A 1 B 5 C 3 D 0 U 4

343 shooters can you give us a break down of numbers of shooters and what classes they are in like in this link, click, how is the prize table going to work thanks matt

From the rule book Flyin i see that differently uspsa doesn't recognize combined divisions so the HOA would be for production and i see them moving him up for the HOA in production

that would only be 15%, those between 60% and 75%

Thank you, I wasn't able to find it last night. Also the first place shooting production dropped more then 7 C's (I out scored him points wise on each stage), but he still whooped me lol. 1 Matt H. 133 A Production 306 0 26.68 11.4693 320.0000 100.00% 306 out of 320 is only 7c's down

first thing i notice you need to be looking at the production only scores on the weld county practical shooters page of the uspsa.com website under local match results to get an accurate picture of the points because you are comparing all the hit factors of the match when only the division you are shooting in matters second the hit factor was high almost 11.5 time was much more important than point even though the winner in production only dropped 7 C's

4.3.1.4 Various sizes of metal plates may be used (see Appendix B5), however, metal plates must not be used exclusively in a course of fire. At least one authorized paper target or Popper must be included in each course of fire.

Robert if you set the dates the other matches will have to work around you, and the end of may would be good

how many to be on the approved list?

...

hey ron can you post an update on the number and class in each division thanks matt