LarryP Posted August 21, 2009 Share Posted August 21, 2009 I always used WSP for my 9 MM & .40 S&W reloads! With the shortage I'll buy almost anything (only brand turned down so far is Wolf.) I just bought Remington No. 1 1/2 Sm Pist Primers and noticed a "Safety Warning" on the Remington that says" Do not use in high intensity cartridges such as 357 Mag, 357 Sig, and .40 S&W". I checked on their web site and they recomment No. 5 1/2. 2 questions: A) Is this for real (cant use No. 1 1/2 in my .40 reloads.) What about Wolf Primers (Are they as good as Win, CCI, or Fed?) Thanks Link to comment Share on other sites More sharing options...
kamikaze1a Posted August 22, 2009 Share Posted August 22, 2009 I checked a box of 1 1/2 sp primers and you are right! Odd that they would say that using standard in place of magnum is hazardous. The other way around I can see...anyone have any 5 1/2? Is it labeled "Magnum" primers? Link to comment Share on other sites More sharing options...
SA Friday Posted August 22, 2009 Share Posted August 22, 2009 Not odd at all. They are concerned about pierced primers from the thinner cup vs the burn ratio. I use SRP's of various manufacturer in certain pistol loads and have tested them against SPP mags and SPP's of the same manufacturer. The pf difference is minimal, well within what you would see batch to batch of ammo. BTW, the biggest velocity spreads I have ever seen in test loads are with Rem primers. I don't know why, but one round is 1000fps the next is 920 fps... I don't get this with other brands I've tested. Link to comment Share on other sites More sharing options...
GrumpyOne Posted August 22, 2009 Share Posted August 22, 2009 I haven't had too good of luck with the Remington SPP. It seems that quite a few juat wouldn't set off, almost like a light strike. Put them back in, hammer them again, they fire. Now, this was all in my auto's, in a revo, they seem to do fine. Link to comment Share on other sites More sharing options...
kamikaze1a Posted August 22, 2009 Share Posted August 22, 2009 I too have used srp for handgun rounds with good results. The odd part was that Remington was saying that loading standard primers in place of hotter magnum primers is hazardous. The other way around I could understand and it could just be to cover their behinds... Link to comment Share on other sites More sharing options...
Guy Neill Posted August 22, 2009 Share Posted August 22, 2009 Strange that they do not include the 9mm Luger as well since it and the 40 S&W are listed as having the same pressure allowance in SAAMI. Looking at some Remington 1½ primers I bought withing the last two weeks, they do not have such a statement. Guy Link to comment Share on other sites More sharing options...
kamikaze1a Posted August 26, 2009 Share Posted August 26, 2009 I usually load with WW primers and only have this one brick of Rem. It might be older as I traded it for a brick of WLP a while back. Don't see any date codes so no telling how old it is... Link to comment Share on other sites More sharing options...
Joe4d Posted August 26, 2009 Share Posted August 26, 2009 By the way, dont pass up wolf, they are a little hard and require a bit more pressure to seat on a dillon but they work fine and always go bang. Link to comment Share on other sites More sharing options...
Harmon Posted September 1, 2009 Share Posted September 1, 2009 ive had more blown 9mm remington primers than anything...some even in factory ammo. it seems like the cups are thin, but the metal is hard.... these were regular 9mm minor ammo...loaded with 147 fmj and win 231. Harmon Link to comment Share on other sites More sharing options...
CGT80 Posted September 5, 2009 Share Posted September 5, 2009 I just noticed, the other night, the same warning on a box of Remington primers that I got in a trade. In my load book, 40 cal will reach pressures of 22,000psi and 9mm will reach 32,000 psi. If this is the case, why is 9mm not listed in the warning? I loaded up 165 rounds of rainier 180fp copper coated bullets over 4.3 grains of win 231, seated to 1.125" with Remington small pistol primers. I will check a few cases when I first start to shoot them. I think/hope they will work fine. I also have some cci small pistol primers that I have not tried yet. Is there any noticeable difference between Winchester and cci? Thanks Chris ive had more blown 9mm Remington primers than anything...some even in factory ammo.it seems like the cups are thin, but the metal is hard.... these were regular 9mm minor ammo...loaded with 147 fmj and win 231. Harmon Link to comment Share on other sites More sharing options...
G-ManBart Posted September 6, 2009 Share Posted September 6, 2009 I just noticed, the other night, the same warning on a box of Remington primers that I got in a trade. In my load book, 40 cal will reach pressures of 22,000psi and 9mm will reach 32,000 psi. If this is the case, why is 9mm not listed in the warning? SAAMI spec max pressure for .40 is 35,000 PSI....9mm is the same. R, Link to comment Share on other sites More sharing options...
Y. Koester Posted September 6, 2009 Share Posted September 6, 2009 I always used WSP for my 9 MM & .40 S&W reloads! With the shortage I'll buy almost anything (only brand turned down so far is Wolf.) I just bought Remington No. 1 1/2 Sm Pist Primers and noticed a "Safety Warning" on the Remington that says" Do not use in high intensity cartridges such as 357 Mag, 357 Sig, and .40 S&W". I checked on their web site and they recomment No. 5 1/2.2 questions: A) Is this for real (cant use No. 1 1/2 in my .40 reloads.) What about Wolf Primers (Are they as good as Win, CCI, or Fed?) Thanks I have loaded about 5k small rifle wolf primers with no problems, in my 40 limited gun. So yeah I think that they are fine. Link to comment Share on other sites More sharing options...
RPM618 Posted September 10, 2009 Share Posted September 10, 2009 I always used WSP for my 9 MM & .40 S&W reloads! With the shortage I'll buy almost anything (only brand turned down so far is Wolf.) I just bought Remington No. 1 1/2 Sm Pist Primers and noticed a "Safety Warning" on the Remington that says" Do not use in high intensity cartridges such as 357 Mag, 357 Sig, and .40 S&W". I checked on their web site and they recomment No. 5 1/2.2 questions: A) Is this for real (cant use No. 1 1/2 in my .40 reloads.) What about Wolf Primers (Are they as good as Win, CCI, or Fed?) Thanks I bought 1K Wolf large pistol to load 45 ACP and they have performed well. I have had no problems with any of the rounds loaded with them. (230 gr LRN with 3.9 gr Clays) Link to comment Share on other sites More sharing options...
CGT80 Posted September 10, 2009 Share Posted September 10, 2009 I tried out the remington small pistol primers in my 40 xd with light to medium loads and had no problems. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now