nvmichael Posted February 3, 2008 Share Posted February 3, 2008 On your comp / range S&W revolvers, do you remove the hammer block or leave it in? Does removing it result in a lighter DA pull? I understand the safety consequences. Thanks Link to comment Share on other sites More sharing options...
HighVelocity Posted February 3, 2008 Share Posted February 3, 2008 I can tell no difference in trigger pull with or without the hammer block in place. I keep mine installed for the obvious safety reasons. Gary J. Link to comment Share on other sites More sharing options...
Carmoney Posted February 3, 2008 Share Posted February 3, 2008 Many people do not in fact understand that the hammer block is nothing more than a safety redundancy, and that the true primary "drop safety" on a S&W revolver is the interplay between the hammer foot and the rebound slide. Unless the trigger is back, the hammer is blocked by the rebound slide and cannot move forward to fire the gun. Although the difference is usually minimal, the hammer block introduces an extra level of potential friction into the DA trigger pull. In a few instances, I have seen the hammer block create significant glitchiness in the action. I always remove them in my competition action jobs, and on all my own personal competition revolvers. Link to comment Share on other sites More sharing options...
Waltermitty Posted February 3, 2008 Share Posted February 3, 2008 Belt & Suspenders. I only use both when I don't trust my pants. Link to comment Share on other sites More sharing options...
HSMITH Posted February 4, 2008 Share Posted February 4, 2008 I leave them, if they affect the pull I will fix them, usually they don't affect it much if at all. Link to comment Share on other sites More sharing options...
Tom E Posted February 4, 2008 Share Posted February 4, 2008 I keep them in a ziplock bag. They don't help the gun go bang and as Carmoney said, are redundant. My hammer is completely below the frame surfaces before it contacts the firing pin Link to comment Share on other sites More sharing options...
nvmichael Posted February 4, 2008 Author Share Posted February 4, 2008 Thank you for the replys. I'm takin' it out! Link to comment Share on other sites More sharing options...
bountyhunter Posted February 4, 2008 Share Posted February 4, 2008 On your comp / range S&W revolvers, do you remove the hammer block or leave it in?Does removing it result in a lighter DA pull? I understand the safety consequences. Thanks It doesn't change the trigger pull. I take them out of my comp revos because they rattle. I leave it in my defense pistol. Link to comment Share on other sites More sharing options...
bountyhunter Posted February 4, 2008 Share Posted February 4, 2008 Many people do not in fact understand that the hammer block is nothing more than a safety redundancy, and that the true primary "drop safety" on a S&W revolver is the interplay between the hammer foot and the rebound slide. Unless the trigger is back, the hammer is blocked by the rebound slide and cannot move forward to fire the gun. The argument I hear is that if dropped on the hammer spur, the hammer can break and still impact the round and the "safety block" is specifically intended to stop this. Chances of that happening are pretty remote. Link to comment Share on other sites More sharing options...
Tom E Posted February 4, 2008 Share Posted February 4, 2008 (edited) Many people do not in fact understand that the hammer block is nothing more than a safety redundancy, and that the true primary "drop safety" on a S&W revolver is the interplay between the hammer foot and the rebound slide. Unless the trigger is back, the hammer is blocked by the rebound slide and cannot move forward to fire the gun. The argument I hear is that if dropped on the hammer spur, the hammer can break and still impact the round and the "safety block" is specifically intended to stop this. Chances of that happening are pretty remote. Probability is right up there with being struck by lightning while reading this post. This is being discussed on the "old womens" S&W Forum also. Read and be enlightened: http://smith-wessonforum.com/eve/forums/a/...04/m/2441013872 Edited February 4, 2008 by Tom E Link to comment Share on other sites More sharing options...
cooper_999 Posted February 4, 2008 Share Posted February 4, 2008 Belt & Suspenders.I only use both when I don't trust my pants. fantastic.... sorry, nothing to say ontopic (except, that all my revos miss that thing, too), but I laughed so loud when I read this post, I thought, I should tell Waltermitty DVC, Sascha Link to comment Share on other sites More sharing options...
cliffwalsh Posted February 4, 2008 Share Posted February 4, 2008 I melt mine down for the silver.. Link to comment Share on other sites More sharing options...
20nickels Posted February 5, 2008 Share Posted February 5, 2008 Out, but make sure your rebound spring is strong enough to activate your primary (and now only) top-of-rebound slide safety. Link to comment Share on other sites More sharing options...
JamesLovesJammie Posted February 5, 2008 Share Posted February 5, 2008 Sounds like it was designed by "The Department of Redundancy Department" Mine went out when I did the Jerry M. Trigger Job DVD, even though he suggested to leave it in. Link to comment Share on other sites More sharing options...
Waltermitty Posted February 5, 2008 Share Posted February 5, 2008 Belt & Suspenders.I only use both when I don't trust my pants. fantastic.... sorry, nothing to say ontopic (except, that all my revos miss that thing, too), but I laughed so loud when I read this post, I thought, I should tell Waltermitty DVC, Sascha Then I have earned my keep for the day. Prost! Link to comment Share on other sites More sharing options...
professor Posted February 6, 2008 Share Posted February 6, 2008 Many people do not in fact understand that the hammer block is nothing more than a safety redundancy, and that the true primary "drop safety" on a S&W revolver is the interplay between the hammer foot and the rebound slide. Unless the trigger is back, the hammer is blocked by the rebound slide and cannot move forward to fire the gun. The argument I hear is that if dropped on the hammer spur, the hammer can break and still impact the round and the "safety block" is specifically intended to stop this. Chances of that happening are pretty remote. What hammer spur? Link to comment Share on other sites More sharing options...
Bubber Posted February 6, 2008 Share Posted February 6, 2008 From what I have been informed is that incase the hammer pivot pin is broken, and the hammer is struck it can cause the firing pin to make caontact with the primer. I can check this out when time permits as I can remove my hammer pivot pin from an old S&W. It was repaired prior to me knowing that I could just send it off to the factory for repairs... later rdd Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now