ChrisMcCracken Posted February 15, 2007 Share Posted February 15, 2007 Looking on powder valley, they're sold out of Federal #150 Large Pistol primers. Is it ok to get the Federal #155 Large Pistol Mag primers? Whats the difference between the two? I'm looking for a light striking primer to use with Clays in my G30. Thanks! Link to comment Share on other sites More sharing options...
ChrisMcCracken Posted February 15, 2007 Author Share Posted February 15, 2007 Nobody is willing to comment on the difference between fed #150 and #155 or offer an alternate light strike primer? Would small rifle work? Since I've never had them in hand, I'm exactly sure what distinguishes small from large or pistol from rifle with regard to primer shape, size, or function. If powder valley doesn't have what I need, I'll likely buy small quantities locally. Link to comment Share on other sites More sharing options...
Guy Neill Posted February 15, 2007 Share Posted February 15, 2007 The magnum primers have both a different priming formulation and a different cup thickness. The thicker cup may affect ignition reliability (but likely they will fire okay), but the different priming compound will change the ballistics of the load. Small rifle primers will not work in the 45 Auto normally, unless you are using some of the NT cases that use small primer pockets. Large rifle primers are not usable as they are taller than large pistol primers, requiriung a deeper primer pocket. Even though you may prefer Federal larege pistol, if they are unavailable I think it would be better to go with a different large pistol primer than anything else. So, if they have Winchester, CCI or such avaialble, go with thatr over the magnum pistol or any rifle primers. In any component switch, it is prudent to re-develop the load, starting low and working up. Guy Link to comment Share on other sites More sharing options...
Nemo Posted February 15, 2007 Share Posted February 15, 2007 The MagTech primers also seem to be a good alternative and they are cheaper. I think your Glock shouldn't have a prblem with those or the Winchesters. The worked up revolvers are more sensitive to primer cup hardness. Link to comment Share on other sites More sharing options...
ChrisMcCracken Posted February 15, 2007 Author Share Posted February 15, 2007 I've had a problem with light strikes in the past using WWB, prompting me to use a stronger striker spring, the 28 newton red factory spring to be specific. I will likely switch back with handloads. Thanks for the explanation, Guy; it was very helpful. I'll consider the magtechs; thanks, Nemo. Chris Link to comment Share on other sites More sharing options...
Harmon Posted February 15, 2007 Share Posted February 15, 2007 look somewhere else for federal 150s...those are what you want in 45acp. looks like primers are expensive all over the place...heres a good place to start: Federal 150s while ordering, you might as well get a pound or two of some other powders to tinker with. Harmon Link to comment Share on other sites More sharing options...
dajarrel Posted February 15, 2007 Share Posted February 15, 2007 I came across three boxes the other night for $22.95/box. I jumped all over them. With tax I paid about $75. Used to be able to get 5000 for that price. ----sigh---- dj Link to comment Share on other sites More sharing options...
Bronson7 Posted February 15, 2007 Share Posted February 15, 2007 Looking on powder valley, they're sold out of Federal #150 Large Pistol primers. Is it ok to get the Federal #155 Large Pistol Mag primers? Whats the difference between the two?I'm looking for a light striking primer to use with Clays in my G30. Thanks! I take it you're using a reduced striker spring? If so, as you know, Federal large pistol is the way to go. If you're using the stock striker spring, you'll be fine with Winchester. You'll get fail to fires using Winchesters and the reduced power striker spring (I know first hand from my G30). Bronson7 Link to comment Share on other sites More sharing options...
ChrisMcCracken Posted February 15, 2007 Author Share Posted February 15, 2007 Looking on powder valley, they're sold out of Federal #150 Large Pistol primers. Is it ok to get the Federal #155 Large Pistol Mag primers? Whats the difference between the two? I'm looking for a light striking primer to use with Clays in my G30. Thanks! I take it you're using a reduced striker spring? If so, as you know, Federal large pistol is the way to go. If you're using the stock striker spring, you'll be fine with Winchester. You'll get fail to fires using Winchesters and the reduced power striker spring (I know first hand from my G30). Bronson7 Acutally, I'm using one of the red factory springs, 28 newtons, due to some fail to fires with WWB when I was using the stock spring. I would like to go back to the stock spring or to a reduced spring, so the Federal's are pretty much my only choice from the way it sounds. Chris Link to comment Share on other sites More sharing options...
DougCarden Posted February 15, 2007 Share Posted February 15, 2007 Chris, In my limited experience with Fed's magnum primers they are as sensitive as the reg primers but give you anywhere from 15 to35 fps more due to being a little hotter. I know this to be true with the small pistol, but have never used the large magnum primers. If they are decently priced, I would buy them and shoot them, no thinking involved DougC Link to comment Share on other sites More sharing options...
ima45dv8 Posted February 17, 2007 Share Posted February 17, 2007 Looking on powder valley, they're sold out of Federal #150 Large Pistol primers. Is it ok to get the Federal #155 Large Pistol Mag primers? Whats the difference between the two? I'm looking for a light striking primer to use with Clays in my G30. Thanks! I take it you're using a reduced striker spring? If so, as you know, Federal large pistol is the way to go. If you're using the stock striker spring, you'll be fine with Winchester. You'll get fail to fires using Winchesters and the reduced power striker spring (I know first hand from my G30). Bronson7 Acutally, I'm using one of the red factory springs, 28 newtons, due to some fail to fires with WWB when I was using the stock spring. I would like to go back to the stock spring or to a reduced spring, so the Federal's are pretty much my only choice from the way it sounds. Chris Just for grins, put in the stock striker spring, and a heavier recoil spring. There's a chance your light strikes are because the recoil spring is not holding the gun in battery when you pull the trigger. Link to comment Share on other sites More sharing options...
Bronson7 Posted February 17, 2007 Share Posted February 17, 2007 (edited) Looking on powder valley, they're sold out of Federal #150 Large Pistol primers. Is it ok to get the Federal #155 Large Pistol Mag primers? Whats the difference between the two?I'm looking for a light striking primer to use with Clays in my G30. Thanks! Erucolindon, there's one more thing you may want to check. Glock revised the trigger bar on the G21 and G30. On some guns, the vertical trigger bar extension wasn't pushing the firing pin safety up far enough. It would go high enough to fire but had just a slight drag; enough to possibly cause a failure to fire. In addition, I believe the trigger bar is also slightly longer in order to pull the striker back just a little further for some added oomph. The new trigger bar is part# 4256-1. Check yours and see if it has it. Bronson7 Edited February 17, 2007 by Bronson7 Link to comment Share on other sites More sharing options...
ChrisMcCracken Posted February 18, 2007 Author Share Posted February 18, 2007 Thanks guys! I've already got a stronger recoil spring, a dual stage recoil reduction spring from Alpha & Omega Gun works, but I'll probably switch back for lighter loads. My trigger bar is #4256, so I probably have the older bar. I'll look into getting one of the newer ones. That would definitely make a difference. I appreciate the tips! Chris Link to comment Share on other sites More sharing options...
TonyT Posted February 18, 2007 Share Posted February 18, 2007 Stick with Federal standard large pistol primers for use in lightened DA revolvers. For semi-auto I use the Winchester large pistol primer, highly uniform velocities. Link to comment Share on other sites More sharing options...
ChrisMcCracken Posted February 21, 2007 Author Share Posted February 21, 2007 (edited) So it turns out gamaliel, powder valley, and midway are all out of federal #150 large pistol primers. Anyone know of another source? Edit: Nevermind, I placed an order with T&T. Lets see if they actually have them in stock. Edited February 21, 2007 by Erucolindon Link to comment Share on other sites More sharing options...
DEADEYE Posted February 22, 2007 Share Posted February 22, 2007 (edited) FYI; For years Winchester didn't make a Mangum primer if you read on the package it said for standard and magnum ....... I have used Winchester for years because of this it limits my primer inventory. I have used standard winchesters in 300 mag without an issue. For a source try Mid South shooters supply or Natchez Shooter supply. Edited February 22, 2007 by DEADEYE Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now