mloch Posted July 14, 2017 Share Posted July 14, 2017 Hey! I have done a grip Job on my P320 (adding silicium carbide with J-B weld). It is a problem ... rule wise ... in USPSA Production ... that the silicium carbide extends up to the slide lock lever? On the second picture you can see that the covered grip surface extends a tiny bit higher than the Talon Grip Tape. Just want to play safe before heading to the Nationals later in September. Thanks in advance! See you, Marijan Link to comment Share on other sites More sharing options...
rooster Posted July 14, 2017 Share Posted July 14, 2017 I could be wrong but it looks legal to me. Link to comment Share on other sites More sharing options...
alma Posted July 14, 2017 Share Posted July 14, 2017 That looks very similar to the pattern I lay down. It should be legal. I have worked on many grips that have been used at Production Nationals and other majors. This has never been an issue. Link to comment Share on other sites More sharing options...
sfinney Posted July 14, 2017 Share Posted July 14, 2017 You are still in the "grip" area, not an issue. If you put grit on the trigger guard, or thumb pads forward on the frame, it would be no go. But anywhere in the grip panel area should be fine. The diagram in the rulebook is a general representation, not an absolute. Link to comment Share on other sites More sharing options...
mloch Posted July 18, 2017 Author Share Posted July 18, 2017 @all Thx for the help! Link to comment Share on other sites More sharing options...
gng4life Posted July 18, 2017 Share Posted July 18, 2017 Yes, you should be good. The rule states that stippling has to follow the illustrations in the book and no grip tape can be applied to any lever or button, up to it but not including it with any gripping texturing/grip tape, you are good. Of course, the official RM at the match is the final authority but according to the pictures you provided, I can't see any RM disputing the legality of your grip. Link to comment Share on other sites More sharing options...
gng4life Posted July 18, 2017 Share Posted July 18, 2017 Just curious, would this be better suited for the rules section? Link to comment Share on other sites More sharing options...
Sig0431 Posted July 18, 2017 Share Posted July 18, 2017 Kind of off topic but I would like to see a write up of how to do this and where to get the supplies! I am tired of having to replace grip tape all the time. Link to comment Share on other sites More sharing options...
BillGarlandJr Posted July 18, 2017 Share Posted July 18, 2017 Alma has a very good video on YouTube showing how its done. Link to comment Share on other sites More sharing options...
mloch Posted July 19, 2017 Author Share Posted July 19, 2017 I have written a detailed how-to-manual for a german gun magazine as a part of a Glock Tuning Special. I will post the pics here asap ;-) Link to comment Share on other sites More sharing options...
Sig0431 Posted July 19, 2017 Share Posted July 19, 2017 14 hours ago, mloch said: I have written a detailed how-to-manual for a german gun magazine as a part of a Glock Tuning Special. I will post the pics here asap ;-) Thanks! That would be awesome! Link to comment Share on other sites More sharing options...
Sig0431 Posted July 19, 2017 Share Posted July 19, 2017 On 7/18/2017 at 0:10 PM, BillGarlandJr said: Alma has a very good video on YouTube showing how its done. I will go searching for that now. Thanks for the lead Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 On 7/19/2017 at 0:21 AM, mloch said: I have written a detailed how-to-manual for a german gun magazine as a part of a Glock Tuning Special. I will post the pics here asap ;-) I have been doing a fair amount of research on this. Do you happen to have a grit recommendation? I have seen many say 80 grit and even some say to do a 50/50 mix of 80 and 120 grit. I fully understand that this comes down to personal preference but just wondering what you have found that you like. I use pro grip liquid all the time as my hands seem to sweat a lot in the desert so grip tape is my world. But I do not want to go so harsh that I am bleeding after a stage haha. Link to comment Share on other sites More sharing options...
mloch Posted July 20, 2017 Author Share Posted July 20, 2017 Link to comment Share on other sites More sharing options...
mloch Posted July 20, 2017 Author Share Posted July 20, 2017 Concerning grit size ... I have used 60 grit and it is a bit more coarse than skateboard tape. Link to comment Share on other sites More sharing options...
BC27 Posted July 20, 2017 Share Posted July 20, 2017 1 hour ago, mloch said: Concerning grit size ... I have used 60 grit and it is a bit more coarse than skateboard tape. I'm getting ready to do this as well. What kind of adhesive did you use? Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 36 minutes ago, BC27 said: I'm getting ready to do this as well. What kind of adhesive did you use? Check out this post. Alma posts his video on Page 2. Link to comment Share on other sites More sharing options...
BC27 Posted July 20, 2017 Share Posted July 20, 2017 13 minutes ago, Sig0431 said: Check out this post. Alma posts his video on Page 2. Cool, Thanks! BTW, I found this place that has various grit sizes for a reasonable price: http://www.hisglassworks.com/shop/loose-grit/silicon-carbide/1-pound.html Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 1 minute ago, BC27 said: Cool, Thanks! BTW, I found this place that has various grit sizes for a reasonable price: http://www.hisglassworks.com/shop/loose-grit/silicon-carbide/1-pound.html I was going to share that link as well. Amazon is way over priced. I think I will be going with that website. Link to comment Share on other sites More sharing options...
BC27 Posted July 20, 2017 Share Posted July 20, 2017 8 minutes ago, Sig0431 said: I was going to share that link as well. Amazon is way over priced. I think I will be going with that website. Yeah, $4 is very reasonable and we don't need much. Which size grit are you going with? I'm thinking I'll order 60 and 80 and make a test patch on a piece of plastic so I can decide which to use. Maybe even mix the 60 and 80 if I'm on the fence. Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 1 minute ago, BC27 said: Yeah, $4 is very reasonable and we don't need much. Which size grit are you going with? I'm thinking I'll order 60 and 80 and make a test patch on a piece of plastic so I can decide which to use. Maybe even mix the 60 and 80 if I'm on the fence. I was thinking the same thing. I have seen the grips that Alma has but he uses a 30-ish grit that comes with a harbor freight kit, from what I have seen 60 grit looks like what I am looking for and I do not think I have seen a 8 yet but I think that would be way to smooth. I wonder if anyone knows the grit of the grip tape from springer as that would provide a good idea for me. But for $4 not like we would be loosing much money. Link to comment Share on other sites More sharing options...
BC27 Posted July 20, 2017 Share Posted July 20, 2017 2 minutes ago, Sig0431 said: I was thinking the same thing. I have seen the grips that Alma has but he uses a 30-ish grit that comes with a harbor freight kit, from what I have seen 60 grit looks like what I am looking for and I do not think I have seen a 8 yet but I think that would be way to smooth. I wonder if anyone knows the grit of the grip tape from springer as that would provide a good idea for me. But for $4 not like we would be loosing much money. Ok, I was curious what the Harbor Freight grit size was. if it's around 30 grit, then 60 should be good. I'll probably get the 80 as well only because $4 bucks is cheap insurance in case the 60 is coarser than I'm expecting. Thanks again for the info. Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 2 minutes ago, BC27 said: Ok, I was curious what the Harbor Freight grit size was. if it's around 30 grit, then 60 should be good. I'll probably get the 80 as well only because $4 bucks is cheap insurance in case the 60 is coarser than I'm expecting. Thanks again for the info. I was also given this link that has some other options for grits. http://therockshed.com/grit1.html Link to comment Share on other sites More sharing options...
BC27 Posted July 20, 2017 Share Posted July 20, 2017 1 minute ago, Sig0431 said: I was also given this link that has some other options for grits. http://therockshed.com/grit1.html Thank you! I'll probably get the 36 and 46-70. Link to comment Share on other sites More sharing options...
Sig0431 Posted July 20, 2017 Share Posted July 20, 2017 Just now, BC27 said: Thank you! I'll probably get the 36 and 46-70. I am placing a order now for 1 lb of 60/90, 36 and 46/70. If you have not placed an order by the time I get it I will take some pictures next to grip tape I have and let you know what I think. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now