Why1504 Posted December 29, 2015 Share Posted December 29, 2015 Over the holidays one of my goals has been to stabilize my 1050. This began with adding another layer of plywood to the top, more screws into the wall... All the normal stuff. This did help but not as much as expected. I got my best results from adding a brace to the case feeder. Instead of following the pack and bracing to the wall, we angled this down to the table. The press doesn't move at all now. The brace is set at about a 60 degree angle from the top of the case feeder square tube down to the table. We used aluminum square tube with a U bolt at the top and a fabbed angle bracket at the bottom that is screwed into the table. Link to comment Share on other sites More sharing options...
Tom S. Posted December 29, 2015 Share Posted December 29, 2015 (edited) People seldom stop to think about it, but the case feeder (on the 650 too) is like a big pry bar on the side of the press, and the more cases it has in it, the more pressure it can exert. That was one of the reasons I shortened the stand tubing on my 650. Edited December 29, 2015 by Tom S. Link to comment Share on other sites More sharing options...
Why1504 Posted December 31, 2015 Author Share Posted December 31, 2015 This has improved every aspect of the operation of my 1050. It has solved multiple small problems. Link to comment Share on other sites More sharing options...
Foxbat Posted December 31, 2015 Share Posted December 31, 2015 I put a vertical bar under each press, it is bolted on top, and anchored to the concrete floor. It eliminates almost all shake as you work the handle. Link to comment Share on other sites More sharing options...
echotango Posted March 2, 2016 Share Posted March 2, 2016 Made a huge difference to the buggy whip. Link to comment Share on other sites More sharing options...
Boxerglocker Posted March 2, 2016 Share Posted March 2, 2016 Great idea, but honestly haven't had many issues with the case feeder, especially since adding my Inline Fabrication 4 inch riser ultramount. It removed any flex off the benchtop by increasing the foot print. I'm planning a new larger bench for this summer though and will definitely plan ahead for bracing both casefeeders. Link to comment Share on other sites More sharing options...
echotango Posted March 2, 2016 Share Posted March 2, 2016 Mine would move a little once the bullet feeder was added. Link to comment Share on other sites More sharing options...
CanonSterVA Posted March 3, 2016 Share Posted March 3, 2016 Great idea, but honestly haven't had many issues with the case feeder, especially since adding my Inline Fabrication 4 inch riser ultramount. It removed any flex off the benchtop by increasing the foot print. I'm planning a new larger bench for this summer though and will definitely plan ahead for bracing both casefeeders. Great looking setup up with the In-Line Ultra Mount. Link to comment Share on other sites More sharing options...
DEP44 Posted March 3, 2016 Share Posted March 3, 2016 I have the "old" Mr Bulletfeeder and use a cable tensioner between the bracket and the wall. Works wonders. Link to comment Share on other sites More sharing options...
bradhe Posted March 5, 2016 Share Posted March 5, 2016 I made a steel plate 12x12x1 out of some scrap that I bolted to the bench and then bolted the 1050 to. Is now rock solid. The leverage on that small base against a wood bench is very difficult to get completely stable Link to comment Share on other sites More sharing options...
tanks Posted March 10, 2016 Share Posted March 10, 2016 Great idea, but honestly haven't had many issues with the case feeder, especially since adding my Inline Fabrication 4 inch riser ultramount. It removed any flex off the benchtop by increasing the foot print. I'm planning a new larger bench for this summer though and will definitely plan ahead for bracing both casefeeders. How far from the edge of the bench is the inline fabrication mount? Also, notice the 1050 is forward of it, how far from the edge is the 1050? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now