ihocky2 Posted May 11, 2014 Share Posted May 11, 2014 Has anyone else experienced this. I tried installing the Nowlin sear spring in my new P14 and the left leg falls short of the sear, it only wants to sit on the trigger bow. Is this common to the P14 or is it problem with this specific brand of spring or maybe a bad spring from the batch? Link to comment Share on other sites More sharing options...
ChuckS Posted May 11, 2014 Share Posted May 11, 2014 The Para slot for the sear spring tab sits a bit lower than standard. Sadly, I forgot the brand of spring I have in mine. I am sure someone will pipe up. (This was true on a P14 and P16 (90's vintage) Later, Chuck Link to comment Share on other sites More sharing options...
Arlin Posted May 11, 2014 Share Posted May 11, 2014 Ihocky2 The springs are special and should be replaced with OEM parts. I get mine from Brownells. Arlin Link to comment Share on other sites More sharing options...
jstagn Posted May 11, 2014 Share Posted May 11, 2014 My old para p14-45 (1995 vintage) takes a standard colt spring. As correctly stated the new para p14-45 pro custom takes a longer spring only made by para (cannot speak of brownells stuff). My new para had to sent back to factory because the slot was too low even with their spring. They fitted a new frame and still a 'colt' (supposely the standard) mainspring will still not fit, however a Clark split spring did fit barley and is working well after over 1k rounds. I have a para spring as a backup and may try to fit it in the future. Link to comment Share on other sites More sharing options...
HI5-O Posted May 12, 2014 Share Posted May 12, 2014 The para sear springs are longer than the typical 1911 sear springs. I have to use one in my STI to keep the left leg of the spring from falling off of the sear. Gun came with a Colt sear spring but the engagement of the left leg was just catching the corner of the sear. Link to comment Share on other sites More sharing options...
ihocky2 Posted May 12, 2014 Author Share Posted May 12, 2014 Thanks for the information. Everything I had read before buying the P14 was that it uses standard 1911 parts except the mag release and trigger. I guess the sear spring should be included in that list. Link to comment Share on other sites More sharing options...
bountyhunter Posted May 13, 2014 Share Posted May 13, 2014 Thanks for the information. Everything I had read before buying the P14 was that it uses standard 1911 parts except the mag release and trigger. I guess the sear spring should be included in that list.My Para 1640 uses a non standard guide rod/reverse bushing. Diameter is a bit larger than standard. Link to comment Share on other sites More sharing options...
ParaGunner Posted May 14, 2014 Share Posted May 14, 2014 Ed Brown hardcore and Infinity tri-glide sear springs work in Paras. Link to comment Share on other sites More sharing options...
jstagn Posted May 14, 2014 Share Posted May 14, 2014 Tried the Ed Brown, too short for my p14-45 pro custom (2013 vintage w/ new 2014 frame). Never tried the Infinity. Link to comment Share on other sites More sharing options...
BoyGlock Posted May 15, 2014 Share Posted May 15, 2014 Why does Para make such uncommon specs? Whats the advantage, if any? Link to comment Share on other sites More sharing options...
SPRSkip Posted May 15, 2014 Share Posted May 15, 2014 Have been looking at the Para brand but this is a show stopper for me think Link to comment Share on other sites More sharing options...
kimberacp Posted May 15, 2014 Share Posted May 15, 2014 what I have seen in the past, some will weld and recut the slot in the frame so that the spring will sit higher. along with that, peen out, the left side of the left leg, so that the sear spring will not move left to right, if there is too much space between the channel or opening in the pistol frame. or place a spot weld on the left side and file it down, so the spring does not move left or right in the channel. I myself would file the slot higher install the spring and stick a piece of feeler gauge to fill in the bottom. after the mainspring housing is on, the spring should not move, if it is a tight fit. sometimes, you just have to mickey mouse it. WTF... it works!! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now