Zmego Posted September 19, 2012 Share Posted September 19, 2012 I have a Burris MTAC scope on the way and I would like to put a throw lever on it. I have previous experience with the MGM Switchview and I really liked the length and leverage it gave. The problem is I am not entirely sure what MGM model to get for the MTAC. I called MGM today and they said to get the one for the Millet DMS (model #SVMDMS) and that it will work for the MTAC. However, I have been shopping on CPWSA.com and their website say that two different models are compatible with the MTAC, the Meopta Meostar and the lever for the Razor HD. I am sufficiently confused and could use some help. Does anyone currently use and MGM Switchview on an MTAC that can confirm what one(s) will work? Thanks for the help. Link to comment Share on other sites More sharing options...
OUshooter Posted September 19, 2012 Share Posted September 19, 2012 I'm in the same boat, and would like to add a wrinkle. Can anyone also confirm that one or all of the above mentioned throw levers will work on with the Burris RAMP mount? The 45deg mounts look awfully close. Link to comment Share on other sites More sharing options...
rtr Posted September 19, 2012 Share Posted September 19, 2012 Our MTAC lever will work for both of the situations described. Link to comment Share on other sites More sharing options...
2MoreChains Posted September 19, 2012 Share Posted September 19, 2012 I can confirm that the MGM Switchview intended for the DMS Millett works on the Burris MTac. I did have one problem though, the screws are a tad too short since the diameter of the MTac is a hair bigger than the Millett. One solution is to get longer screws from a screw shop, or the other option (the one I did) was to countersink the screw holes slightly. Link to comment Share on other sites More sharing options...
DonT Posted September 19, 2012 Share Posted September 19, 2012 I recently went through the same thing and chose the MGM SVIORCQB. There's only 0.013 difference in the size of the IOR and the MTAC according to MGM website. The SVIORCQB tightened up nicely with room to spare using the screws provided. I decided to give this one a try because I didn't like the lug cut out in the DMS Millet. Works great. Hope this helps. Link to comment Share on other sites More sharing options...
MarkCO Posted September 19, 2012 Share Posted September 19, 2012 I have the MGM for the Millet DMS on mine, works great. Link to comment Share on other sites More sharing options...
njd Posted September 22, 2012 Share Posted September 22, 2012 (edited) I have an MGM SwitchView for the Meopta Meostar on one MTAC - fits and works fine. My other MTAC wears a fishing reel holder that works good too. $23.29 shipped (for TWO) I use the NC-1 model One thing about the fishing gear - if / when the lever hits the edge of a dump barrel it is unlikely the scope will be damaged The picture below is close, but not exactly what you get - on the NC1 there is a plastic flange 'inside' the flange the nut pushes on. This inner piece engages quite positively with the knurl on the MTAC zoom ring. After installing I cut off the extra 'tails' flush with the nut - there are plenty of threads left to get it back off and on. Edited September 22, 2012 by njd Link to comment Share on other sites More sharing options...
releo 37 Posted September 23, 2012 Share Posted September 23, 2012 Will the MGM work on the 1.5 X 6 MTAC also? Thanks Link to comment Share on other sites More sharing options...
MarkCO Posted September 23, 2012 Share Posted September 23, 2012 1.5-6 power ring is larger. Link to comment Share on other sites More sharing options...
Jaxshooter Posted September 23, 2012 Share Posted September 23, 2012 Does anybody know if the IOR model will fit the regular IOR 1-4 scope (not the one that jumps from 1-4). any information is appreciated. Link to comment Share on other sites More sharing options...
TomMcC Posted September 25, 2012 Share Posted September 25, 2012 I'm using the new 3 Gun Stuff polymer zoomer. It's a nice piece of gear, fit perfectly, is super light weight, and is relatively inexpensive. The only thing I might change is the dark blue color of the polymer, but it's not a big deal. Link to comment Share on other sites More sharing options...
HellsCanyonArmory Posted October 9, 2012 Share Posted October 9, 2012 We have our own engraved switchviews from MGM with our logo's on them. If anybody is interested let me know... I ran one for the first time this year and loved the way it handled. http://www.hellscanyonarmory.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/img_0181.jpg[/img} http://www.hellscanyonarmory.com/index.php/hca-switchview-lever-by-mgm.html Mike Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now