BMartens Posted April 22, 2010 Share Posted April 22, 2010 If they aren't very dirty I just use the Kleanbore nylon brush, put a .30 caliber cleaning patch over it and run it into the mag pushing the follower down. Couple of swipes will get rid of dust and grit most of the time. If it still sounds/feels gritty you'll need to strip it. With a little practice you can strip the CMC's and be back in business pretty quickly. Link to comment Share on other sites More sharing options...
BillD Posted April 22, 2010 Share Posted April 22, 2010 (edited) I cleaned mine after Area 6. I had several that were feeling gritty when I loaded them, probably due to that red dust that was everywhere. I hadn't had any problems with them failing due to grit, rocks or dirt in them (47D's). Edited April 22, 2010 by BillD Link to comment Share on other sites More sharing options...
usmc1974 Posted April 22, 2010 Share Posted April 22, 2010 Never.. so far. If I dropped them in mud, it would be a different story, but the normal range dirt, etc.. never bothered mine. Maybe I'm living on borrowed time. I did by a Arredondo mag cleaner brush, I think I used once on STI mags. What he said. Link to comment Share on other sites More sharing options...
Putty Posted April 22, 2010 Share Posted April 22, 2010 The base pads on mine pop off really easily but the lips that hold the metal plate wont allow the spring to just pop out. I seem to have to wiggle the each loop of the spring over the lips. Same here. I tried to clean them between stages and didnt have enough time so I just tapped and blew on them. Link to comment Share on other sites More sharing options...
Sidewinder6 Posted April 22, 2010 Share Posted April 22, 2010 CMC Power8's. About 35 of them. I always wipe them down on the outside and make sure they are free of dust after dropping them on reloads. But, I replace the springs every few months because I shoot a lot. I use a solution of Simple Green and water to completely clean and degrease the tubes and followers. I purchased a mag brush from Brownells and run it through the tube once or twice before reassembling. Just like new. Springs are cheap. It is worth not having feeding problems keeping the springs strong. If you compare the lengths of a new versus old spring when you remove it, you see how much they loose with time. Just like recoil springs. Link to comment Share on other sites More sharing options...
EkuJustice Posted April 22, 2010 Share Posted April 22, 2010 Don't have a high tolerence for malfunctions here actually. The mags have never had a problem and that is with them dropping in the dirt not sand Link to comment Share on other sites More sharing options...
steel1212 Posted April 25, 2010 Share Posted April 25, 2010 Oops. Sorry. Kleanbore, not Birchwood Casey. Here is a direct link. http://www.natchezss...fgSubGroup=4578 Kleenbore Products Mag & Mag Well Cleaning Brushes, Swabbing Mop -------------------------------------------------------------------------------- KBMAG204 KB MAG/WEL CL BRSH 45/40/38/10M In Stock $3.49 KBMAG206 KB MAG/WEL CL BRSH AR15/M16/AK4 In Stock $4.49 KBMAG202 MAG/WEL BRSH 22/25/380/9MM STAG In Stock $3.49 KBMAG200 MAG/WEL BRSH 22/25/380/9MM STRA In Stock $3.49 KBMAG208 MAG/WEL SWAB 9MM/38/10MM/40/45 In Stock $3.49 -------------------------------------------------------------------------------- Just what I was looking for thanks! Link to comment Share on other sites More sharing options...
MTBfarms Posted April 25, 2010 Share Posted April 25, 2010 I ought to just drive the service truck to matches and fire up the air compressor. Link to comment Share on other sites More sharing options...
The Happy Gila Posted April 28, 2010 Share Posted April 28, 2010 For all my love for this sport....the only thing I detest is cleaning my SS mags... I normally keep 10-12 CMC Powermags for match purposes. If a few of them get gritty during the match, I send in the second team. If it's a really big round count match....... I hammer every target in hopes of lessening the chances of a mag malfunction... usually dosen't produce very good hits, but my mags run... Cheers! THG Link to comment Share on other sites More sharing options...
cas Posted April 29, 2010 Share Posted April 29, 2010 With my CMC's, when they get dirty they won't drop. I suppose the follower tilts and doesn't have give any pressure to push them out. It's frustrating, but I guess it's better than jams. I feel guilty cleaning my mags while others are taping. Link to comment Share on other sites More sharing options...
IdahoShooter Posted May 3, 2010 Share Posted May 3, 2010 Interesting topic... I've never cleaned any of my 47D at a match before, that is until yesterday. All the open shooters were complaining about having to clean their mags after a stage because there was a forced reload. I was thinking, why??? then I ran the stage, and after I was done, I took a look at my mags that I had dropped. The sand at this range is terrible, and I could feel the grit in the mag pushing it down with my finger... I stripped them down and cleaned them, and it probably took me 5 minutes, cuz I put the spring in the wrong direction on the first one. I don't clean them very often so I forget which way the spring goes. I have dropped mags at my home range, and not had any problem, or remember feeling any grit... but this range was really bad. So now I'm thinking I'll have to keep track of which mags I drop and inspect them to make sure they don't need a quick cleaning. Brian Link to comment Share on other sites More sharing options...
Sean Gaines Posted May 3, 2010 Share Posted May 3, 2010 During a match, everytime it hits the ground. Thats all you have to hear! my thoughts exactly Link to comment Share on other sites More sharing options...
Carmoney Posted May 3, 2010 Share Posted May 3, 2010 During a match, everytime it hits the ground. Thats all you have to hear! my thoughts exactly If everybody is standing around brushing out their mags religiously (whether they truly need it or not), who is doing the work to reset the stage??? Link to comment Share on other sites More sharing options...
HS101 Posted May 3, 2010 Share Posted May 3, 2010 If everybody is standing around brushing out their mags religiously (whether they truly need it or not), who is doing the work to reset the stage??? All of the people who shoot Glocks Link to comment Share on other sites More sharing options...
BillD Posted May 3, 2010 Share Posted May 3, 2010 If everybody is standing around brushing out their mags religiously (whether they truly need it or not), who is doing the work to reset the stage??? All of the people who shoot Glocks I knew they were going to be good for something sooner or later! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now