Fireant

try getting Zero to give you a deal on a bulk purchase if you pick them up. Last year I happened to be going right by the plant and and called ahead to askhow much about 30K 180 JHP would be if I picked them up. They told me (with a straight face) that shipping was included and it would be the same whether I picked them up or had them delivered. I'm a cheap skate by birth, but I'll pay more for someone elses stuff before I'll buy from them again.

I shot this one two saturdays ago. Production 7.84 seconds 40 pts. 5.102 hf. Man I thought I was smokin on this one. It came in at 53.0088% Back to more practicing.

Beven, I know you've sent me the info before, but since I've lost it could you please send me the shipping info and prices to have two tubes tuned with your spring/follower kit and base pads. I'm finnally ready to send these to you.

That's what I've been using since Feb. I have not had any problems so far. I am going to get his new spring and follower when I use all of my current springs though.

Where can I find the interim results on the USPSA site? I've looked, but cannot find it.

Thanks Flex. I'd swear that I'm watching my front sight. Maybe I am looking over the sights instead of through it. I'll watch them when I practice in the morning.

I'm not sure if this is the right place or not. In the last 3 weeks I have all of a sudden developed a new problem. My hits on targets past 10 yards in rapid fire are all low. I mean way low. If I slow fire at a six inch paper plate at 30 yards I can place a whole magazine on the plate. When the timer goes of in a match or practice I aim at the top center of the c zone (I know it's not center mass but I'm trying to compensate) I'm getting two D's at the very bottom of the d zone. I'm centered almost perfect left to right, but I'm about 18 - 20 inches low. At the GA match this weekend one guy on my squad told me that I'm pushing the gun forward as I shoot. I kind of noticed this once when I ran dry and did not realize and dropped the hammer on an empty chamber. How can I fix this problem? Am I doing this expecting the recoil? I shoot limited if that matters. Thanks

Roger, Will they be posting the match book like they have in the past? Thanks

Thanks.

300lb. If you still have it I'll take it. So 11.5 EE fit good? I also were a 13 in Nike, I'll give it a try. How do you like the Falcons?

since they are out of scouts in my size does anyone know where the next best place to buy them is?

Beven, Any chance of getting a picture of where and how to cut your spring/follower for a 140mm 40 cal mag? I bought some at the FL Open and thought I cut it right, but I could only get 17 rds. in it. I kept clipping half a coil at a time until I got a reloadable 19. I know I probably ruined it, that's why I stopped at one so far.

Steve, I just ordered your book. How do you get your beginning par time?

Paul, I wish I'd known you were shooting with us last Sat. I would have liked to have put a face to the name. If you try the ramshot let us know how you like it. If you shoot with any limited guys that try it and like it I'd like to know that also. N320 has been hard to find lately.

I carry my glock as my back up limited gun now that I have an STI. it came in handy last month. My rear sight pin had broken and I had to finish with the Glock. You can not sight a gun in during a match even if you carry an extra rear sight.

I angered me to see the anti's had it tacked onto the lawsuit bill that the USPSA site had us all writing in favor of! Go figure!?

I've searched, but have not found what I'm looking for. I want to scale down the USPSA target to simmulate the sight picture at different distances only on the same wall. I've seen the 1/3 cardboard. I want to be able to put targets on my wall so that some will appear the same as from 10yds. 15yds, 20yds. ex. Is there a formula for a ratio or something to be able to scale them down? (I want the apperance of different distances all on the same wall for a dry fire course in the house.) Thanks

(1*) I have a barley broken in Edge that is blued, want to trade?

Thanks, after looking more closely and realizing what a bone head I am, I got my problem fixed. I can not believe how stupid I am some time.

I've read here that you can measure the crimp and should get about .420" I'm right at .422" and if I crank my crimp die down anymore it shortens the OAL of the round. I've also be told that you can check crimp by pushing down on the bullet and if it slides into the case you need more crimp. When I push in on the bullet it does eventually move in the case. What should I do about the crimp?

I love mine! I had it done by Tripp Research before he stopped doing chrome. The chrome along with my blue Agrip makes my G22 stand out and no one will pick it up by mistake.

Thanks, I'm ready for another run now. This thing runs great.

I've just got my 650 back from Dillon and set everything up. Out of my first 100 rounds 10 would not chamber check. They went in except for the last 1/4 to 1/2 inch. Do I need to lower my sizeing die? I'm using the lee 3 die set without the FCD right now. I also had some bullet shavings on the press afterwards, do I need just a little more bell on the case? Thanks.

Shooter Grrl, Is that a reloadable 20 or do you have to take some out to be able to reload with one in the chamber?

Thanks for the replys. I'm relieved that it's not a major issue as long as I don't loose the pin while field stripping it out of the house.