Frankl03

Lots of great info in the PCC forum! Lately I can't seem to get enough PCCs (Mp5, ARV, AKV, Scorpion...) Just really enjoy shooting them at the range esp the plate racks!

I have been using SR primers in my 9mm loads for some time. I have not reduced the powder. I shoot a number of pccs that I believe benefit from a hotter load. Currently Loading 124 Gr Everglades plated bullet over 4.2 gr Tight Group with the small rifle primers. Works for me.

Way to go! Welcome from KCMO! MN is my home state. Really nice in the summer!

Welcome from KCMO! I have to respectfully disagree about gun control. Gun control takes guns out of the hands of law abiding but has no affect on the lawless.

For my pccs &pistols, I use 4.2 Gr Tight group over a 124 gr Everglades plated bullet. Works great in Pistols and carbines.

I keep looking for the site and don't see it. Are they coming out with a new sight maybe?

Unforgiven Great movie "He said how you was really William Munny out of Missouri... and Bill said: "Same William Munny that dynamited the RockIsland and Pacific in '69 killin' women and children an' all?". And Ned says you done a lot worse than that, said you was more cold blooded than William Bonney or Clay Alisson or the James Brothers and how if he hurt Ned again you was gonna come an' kill him like you killed a U.S. Marshall in '73" Casa Blanca "Play it again Sam"

Have the polymer Rival Dark Side now, great gun! Saving up to get the Rival S. I'm leaning towards the Chrome one.

I switched from a Lee seating die to a Dillion seating dies (Dillion press) . It helped tighten up my variances.

I Start with Hoppe's No. 9 to get the crud out. Then i use Hoppes Elite cleaner and end with Synthetic oil (mobil One) to lube. For stubborn stuff on my Ar9 (9mm Carbines get so dirty) I start with copper cleaner.

Welcome from KCMO! Looks like a great range on your property! I always think of Arkansas as a great gun state.

On my Elite Limited Custom (large frame) Henning base pads fit the magwell perfectly. These did not increase capacity but otherwise worked great: https://www.henningshop.com/Tanfoglio Magazine Base Pads_it-1457256.aspx?CAT=9249 Hope that helps!

I have this trigger installed in my Limited. The pre-travel is adjusted great with almost no take up. How do I adjust the over-travel? I know its the screw in the front of the trigger. Do I turn it clockwise to take out over-travel? Thanks!

I see the P Match pro is DA/SA, whats the name of the one that is SA? I looked at EAA and didn't even see a SA version. Polymer Match I think. I know I answered my own question.

Deleted

Super great deal! Witness elite match is a great pistol.

Thanks! Sounds good zombywoof! Almost makes me want to use the Extreme flat trigger so I can use the canik trigger pin with easy in and easy out.

Hi All, I have a new Witness limited 9mm. I already had it apart and replaced springs and did some polishing. Trigger is under 2 lbs. I want to install the Henning flat trigger. A question I have is will the trigger and trigger bar come when I take out the trigger pin without taking out the sear cage ( be nice not to have to mess with taking out the safety and the sear cage)? Also is there any issues with using the canik trigger pin with the Henning Flat trigger? Thank you!

Same pin When I bought a canik trigger pin for my Limited Patriot defense included a new trigger bar pin as well. This can be used a slave pin (to attach the trigger return spring to the trigger) as well. Hope you can find one!

I have owned a bunch of 1911s but the Elite match had the best SA trigger out of the box and of course you can make a few changes and have a really nice SA trigger.

The Dawson front sight went in easy for me. Just a couple taps.

Delete

OK great thanks!

Hey on the Dawson front sight, whats the trick to getting the set screw in? Its so small but is there a bushing pin that needs to be trimmed or something?

I put the Henning kit (flat trigger, extended firing pin, guide rod and recoil spring, hammer spring etc) for the Match in my Elite Match .40. The kit I bought did not have grips in it like the new kit. The match had the best out of the box trigger of any Gun I have owned.