Duane Thomas Posted May 2, 2009 Share Posted May 2, 2009 Any know off the top of their head if Lone Wolf offers conventionally rifled barrels for the Glock 35 in .40 S&W, 9mm, and .357 SIG? And how much they might cost, assuming their existence? Link to comment Share on other sites More sharing options...
Brian Gonsalves Posted May 2, 2009 Share Posted May 2, 2009 $100.00 http://www.lonewolfdist.com/Detail.aspx?PROD=1036 http://www.lonewolfdist.com/Detail.aspx?PROD=1043 http://www.lonewolfdist.com/Detail.aspx?PROD=1039 Link to comment Share on other sites More sharing options...
L-10_shooter Posted May 2, 2009 Share Posted May 2, 2009 I have the .40 and .40-9mm barrels from them and am very happy with them. Link to comment Share on other sites More sharing options...
Duane Thomas Posted May 2, 2009 Author Share Posted May 2, 2009 Thanks, guys. The Enosverse Group Mind strikes again! Link to comment Share on other sites More sharing options...
LarryP Posted May 2, 2009 Share Posted May 2, 2009 I have one for my 17, 34 & 35. Good barrels, good fitting but very tight and sharp edges. All mine needed a little dremeling (I love to dremel) In zeroing my gun I found my POI a little different but as good or better groups then my stock 34 Glock barrel. Factory ammo fits fine, but I had a problem with my own reloads. No Glock bulges but the chambers are tight and it took a while to break them in. I use them as case guages so everything I shoot out of them fits or you get FT's. A friend was told by a LW rep. to send in 5 spent cartridge cases with his order and they will size the chamber for your brass. I havent talked with him about since, so I don't know if it worked out, but it's worth a call to LW. Link to comment Share on other sites More sharing options...
chirpy Posted May 2, 2009 Share Posted May 2, 2009 I agree with your comment about the forum...but wouldn't it be easier to go the the mfg. just to be safe? Richard Link to comment Share on other sites More sharing options...
Joe D Posted May 3, 2009 Share Posted May 3, 2009 I had a G34 LWD barrel reamed by them to a more reasonable chamber diameter. Mine is now between the original diameter and stock Glock. Closer to stock Glock than original. I sent them 5 loaded rounds that were somewhat over size. The rounds were just a little snug in the stock barrel. BTW it is still a one hole shooter after the chamber reaming. I am actually a little surprised as to how accurate this barrel is. It loves 147 and 160 gr bullets. Link to comment Share on other sites More sharing options...
Five of Clubs Posted May 3, 2009 Share Posted May 3, 2009 Storm Lake also makes barrels that can be found for the same $ if you don't like the wolf logo. I've been very happy with mine. Link to comment Share on other sites More sharing options...
zipper046 Posted May 3, 2009 Share Posted May 3, 2009 I have a LW barrel in my G35. Great barrel for the money. Very accurate, and a good tight chamber. No "glock Bulge", and the brass resizes beautifully. z- Link to comment Share on other sites More sharing options...
M-Bear Posted May 4, 2009 Share Posted May 4, 2009 I have a LW barrel in my G35. Great barrel for the money. Very accurate, and a good tight chamber. No "glock Bulge", and the brass resizes beautifully. z- I measured my Lone wolf and glock chambers and found there is a five thousands of an inch difference. I have had the Lone wolf choke on factory and reloads that the glock ate fine. Link to comment Share on other sites More sharing options...
hal1955 Posted May 5, 2009 Share Posted May 5, 2009 I had a G34 LWD barrel reamed by them to a more reasonable chamber diameter. Mine is now between the original diameter and stock Glock. Closer to stock Glock than original. I sent them 5 loaded rounds that were somewhat over size. The rounds were just a little snug in the stock barrel.BTW it is still a one hole shooter after the chamber reaming. I am actually a little surprised as to how accurate this barrel is. It loves 147 and 160 gr bullets. Why did you have the chamber reamed? Sticky cases? Extraction problems? Link to comment Share on other sites More sharing options...
Joe D Posted May 5, 2009 Share Posted May 5, 2009 The chamber diameter was too small. I was getting a 25% FTF rate. Rounds that would fall into the Glock barrel would not chamber in the LWD. I had a conversation with JR at LWD yesterday about this issue. Link to comment Share on other sites More sharing options...
hal1955 Posted May 5, 2009 Share Posted May 5, 2009 The chamber diameter was too small. I was getting a 25% FTF rate. Rounds that would fall into the Glock barrel would not chamber in the LWD. I had a conversation with JR at LWD yesterday about this issue. My rounds feed ok but I'm having fte's, Seems like the rim of the case being extracted hangs up on the mouth of the case mouth of the top round in the mag. Not sure if it's barrel related.Tried a little more crimp but still hanging up. Link to comment Share on other sites More sharing options...
Harmon Posted May 5, 2009 Share Posted May 5, 2009 i had to get the throat reamed to get mine to work right in 40 caliber... I will never know why they cut such a short rifling leade in their barrels. Harmon Link to comment Share on other sites More sharing options...
Mark R Posted May 6, 2009 Share Posted May 6, 2009 I purchased a LW barrel for a Glock 22 and it would not feed reloaded ammo. Even had a few hickups on factory ammo. I called Danny at LW and he informed me that the barrel dimensions are very tight. He asked me to send him the barrel and he would fix it. He throated the chamber and polished the barrel ramp and chamber. I got it back and haven't had any issues since. He also said that if I ordered another from him to let him know before hand that you reload and he'll get the barrel polished up before it's sent out. For the time and headache he engraved some flames on the barrel...looks cool when the slide is back. I'd recommend LW barrel as long as you let them know up front that you reload. Link to comment Share on other sites More sharing options...
kframe_mike Posted May 6, 2009 Share Posted May 6, 2009 I've got a G22 barrel that needs to go back too.I bought the thing to shoot lead bullets,but its to tight for reliable function.Even with the .400 diameter bullets I get from a local caster.I just need to get a few sized .401,so I can load up 4 dummy rounds to send with it.-Mike Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now