ysrracer Posted December 2, 2022 Share Posted December 2, 2022 I've been using Clays, but I've got 12 pounds of 231. I'm using Bayou Bullets 160gr RN, and Blue 147gr RN. Anybody use it? Link to comment Share on other sites More sharing options...
dannyd Posted December 2, 2022 Share Posted December 2, 2022 I use HP-38 and W231 (same powders) in 38 short with 135 lead swc, but nothing any heavier. Link to comment Share on other sites More sharing options...
gargoil66 Posted December 2, 2022 Share Posted December 2, 2022 13 hours ago, ysrracer said: I've been using Clays, but I've got 12 pounds of 231. I'm using Bayou Bullets 160gr RN, and Blue 147gr RN. Anybody use it? YRR: I used some with some 105's, 125's, and 130's and found the velocities to be pretty low and I fowled the blaster more than I expected. My opinion, it was too slow a powder and although safe to use, just not very efficient. I think you are better off with a faster powder for such a small case capacity. And yes, I too have a lot of 231 and I really like it for most .45 ACP loads I use. GG Link to comment Share on other sites More sharing options...
Toolguy Posted December 2, 2022 Share Posted December 2, 2022 (edited) I've been shooting 231/HP38 with 160 gr. bullets for a few years now, in 38 Short Colt in my 627s with great results. These powders leave a lot of granular trash in the gun until you get up to a certain pressure level, then they burn well, leaving only thin brown soot. I'm running 4 gr. of powder. For a lighter bullet, like 147, you will want to go up a little, maybe to 4.3 or 4.5. Anything between 4 and 5 grains will work, the 4.0 in my guns will knock down all the steel targets reliably with fairly low recoil. I have shot a lot of Bayou Bullets and like them a lot. Edited December 2, 2022 by Toolguy Link to comment Share on other sites More sharing options...
ysrracer Posted December 2, 2022 Author Share Posted December 2, 2022 7 hours ago, Toolguy said: I've been shooting 231/HP38 with 160 gr. bullets for a few years now, in 38 Short Colt in my 627s with great results. These powders leave a lot of granular trash in the gun until you get up to a certain pressure level, then they burn well, leaving only thin brown soot. I'm running 4 gr. of powder. For a lighter bullet, like 147, you will want to go up a little, maybe to 4.3 or 4.5. Anything between 4 and 5 grains will work, the 4.0 in my guns will knock down all the steel targets reliably with fairly low recoil. I have shot a lot of Bayou Bullets and like them a lot. Thanks Link to comment Share on other sites More sharing options...
xjwalt666 Posted December 11, 2022 Share Posted December 11, 2022 I do 3.1gr of 231 with a 160gr SNS at 1.195 and it works pretty well for plates. Even big poppers drop with them and they sound like mouse farts. Link to comment Share on other sites More sharing options...
ysrracer Posted December 11, 2022 Author Share Posted December 11, 2022 33 minutes ago, xjwalt666 said: I do 3.1gr of 231 with a 160gr SNS at 1.195 and it works pretty well for plates. Even big poppers drop with them and they sound like mouse farts. Thanks, do you know the power factor or velocity? Link to comment Share on other sites More sharing options...
xjwalt666 Posted December 11, 2022 Share Posted December 11, 2022 2 hours ago, ysrracer said: Thanks, do you know the power factor or velocity? I never got a chance to chrono this load. It worked well for my need so I didnt bother. It does however leave a bit of unburnt powder and soot in the cylinder so I was going to up it with my next batch. Link to comment Share on other sites More sharing options...
mchapman Posted December 11, 2022 Share Posted December 11, 2022 For me, 231/hp38 and Winchester autocomp and CFE pistol all worked much better and cleaner when loaded on the upper end of the load recommendations Link to comment Share on other sites More sharing options...
tkheard Posted December 11, 2022 Share Posted December 11, 2022 I’m a big fan of N320. It doesn’t require much, and it’s very cool and clean running. I’m not a fan of burning myself on the cylinder on reloads. Link to comment Share on other sites More sharing options...
xjwalt666 Posted December 11, 2022 Share Posted December 11, 2022 1 hour ago, tkheard said: I’m a big fan of N320. It doesn’t require much, and it’s very cool and clean running. I’m not a fan of burning myself on the cylinder on reloads. I used N320 a bit in 9mm, wish I thought of trying it in Short Colts. I really liked how clean it was in the semi auto, I'll have to give it a try next time I grab a jug. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now