DewarsH2O Posted August 24, 2021 Share Posted August 24, 2021 I just bought a TSO in 9mm. This is my 6th CZ, also own a Czechmate, A01LD, Shadow Orange, plus a couple 75's. Gun was shipped to my FFL, did the paperwork and headed home. Once I got it out of the box to clean it, I realized the frame to slide fit is super tight, when you rack it it binds before it will move forward to put a round into battery. Cleaned it super good, light oil, no improvement. Loaded a magazine with S&B 124g took two tries to load a round, gun fires, then the slide binds before it can load a second round. did not want to fire it anymore as obviously this is not right. Also this is the first higher end CZ I have bought that did not have the test fire paper target in the box, which makes me wonder if it was shot at the factory. Is there something stupid I am missing before I contact the selling dealer for help? Link to comment Share on other sites More sharing options...
George16 Posted August 24, 2021 Share Posted August 24, 2021 Check to make sure the screws for the thumb rest are not too long and contacting the slide. If they’re okay, you can put a little bit of lapping compound on the rails and manually cycle it a few times to loosen up the fit a little bit. Link to comment Share on other sites More sharing options...
DewarsH2O Posted August 24, 2021 Author Share Posted August 24, 2021 Good tip on the thumb rest screws, checked that was not it. The binding seems to happen in the area of the frame directly over the grip. Link to comment Share on other sites More sharing options...
HOGRIDER Posted August 24, 2021 Share Posted August 24, 2021 3 hours ago, DewarsH2O said: I just bought a TSO in 9mm. This is my 6th CZ, also own a Czechmate, A01LD, Shadow Orange, plus a couple 75's. Gun was shipped to my FFL, did the paperwork and headed home. Once I got it out of the box to clean it, I realized the frame to slide fit is super tight, when you rack it it binds before it will move forward to put a round into battery. Cleaned it super good, light oil, no improvement. Loaded a magazine with S&B 124g took two tries to load a round, gun fires, then the slide binds before it can load a second round. did not want to fire it anymore as obviously this is not right. Also this is the first higher end CZ I have bought that did not have the test fire paper target in the box, which makes me wonder if it was shot at the factory. Is there something stupid I am missing before I contact the selling dealer for help? I would first strip the barrel and recoil spring assembly out of the slide, lube it well, and just cycle the slide on the frame back and forth to see if it's simply the tight, hand fitting of the slide to frame. If that doesn't identify the problem, then add in the barrel only and try again. Finally put the recoil spring assembly back together and see if there's any component binding. IMO, after experiencing the same thing with my new S2 Orange, you just need to shoot the gun! If it hangs going back into battery, just bump the back of the slide and fire again. Of course this is after well lubing the slide, frame, and barrel contact mating surfaces You will appreciate the tight fitment of the slide to frame once it wears in a bit! These are premium, hand fit pistols! Link to comment Share on other sites More sharing options...
Foxj66 Posted August 24, 2021 Share Posted August 24, 2021 If it is to tight to function please dont try to fix it yourself. Send it in for warranty service using the below link. https://cz-usa.com/support/warranty/ CZ will cover shipping both ways Link to comment Share on other sites More sharing options...
DewarsH2O Posted August 24, 2021 Author Share Posted August 24, 2021 I am going to send it back. Based on how perfectly my other six ran right out of the box, this one must have skipped QC.... Link to comment Share on other sites More sharing options...
assnolax Posted August 25, 2021 Share Posted August 25, 2021 The slide can contact the sear cage. I've had to take a few thousandths off a replacement slide before or when fitting a tac sport to a standard 75 frame Link to comment Share on other sites More sharing options...
regor Posted August 26, 2021 Share Posted August 26, 2021 On of my Czechmates was like this; I figured out the general area of the rails that was too tight and polished it up, checking for fit frequently until it cycled smoothly. Link to comment Share on other sites More sharing options...
bigdave24 Posted September 2, 2021 Share Posted September 2, 2021 I second the recommendation of lapping compound. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now