Newguy Posted October 29, 2005 Author Share Posted October 29, 2005 I finally benchrested the G34 with myself and someone else shooting. At 10-15 yds it grouped at less than 2" with Blazer 115 gr. and a little less with WWB. At 25 yds the groups opened up big time. After reading this thread and others on GT, I've begun to believe that pre-fitted barrels generally don't increase accuracy, except if you have a Glock that's REALLY bad to begin with. I've read some threads on GT where shooters swear that pre-fit KKM or Storm Lake Barrels have dramatically improved their gun's accuracy. I believe them and I also believe people who say it doesn't make a difference. It seems to depend on the gun and the fit of the original barrel. I agree that USPSA targets are large. But, sometimes there's a lot of black and white around them. In fact, I'm seeing fewer wide open targets in matches. I want to know that if I get a mike or D, it's me not the gun. It's about confidence. Link to comment Share on other sites More sharing options...
boo radley Posted October 31, 2005 Share Posted October 31, 2005 ...I want to know that if I get a mike or D, it's me not the gun. It's about confidence. I agree with that, absolutely. I *never* want to wonder -- is it the gun? Given the cost of everything else, the slight additional cost is pretty painless all-in-all. Anyway. Blowing hot and cold on this issue, in a serious way. Shot yesterday and carefully. I now think I might have *lost* a tad of accuracy with the G35 barrel, but not enough to worry about. OTOH, I started getting some decent groups (finally) with the G34 for the first time since I've owned it. They ranged from 1.7" in this picture, at 25y, to about 2.5". All were shot with Blazer 115g brass case. This is a significant difference, from previous experience, and I'm delighted. It's a shame shipping a pistol is such a hassle or expense, or I would have sprung for a fitted Bar-Sto. Link to comment Share on other sites More sharing options...
Newguy Posted November 10, 2005 Author Share Posted November 10, 2005 Not taking anyone's advice (a serious personality flaw), I decided to try a Storm Lake barrel in my G34. Although Storm Lake is cheaper than a KKM barrel, I figured they would shoot about the same. The Storm Lake ran flawlessly. It ate WWB and Blazer without any reliability problems. In short, it was as reliable as the original barrel. Some posters had mentioned tight chambers. Storm Lake may have redesigned their barrels since the chamber was actually a little looser than the Glock barrel. Although the Storm Lake was slightly tighter and had less side-to-side and up-and-down play than the Glock barrel, this didn't seem to translate into any noticeable improvement in accuracy. Both barrels shot about the same. I was a little disappointed since the shiny Storm Lake barrel "looked" like it should be more accurate. Link to comment Share on other sites More sharing options...
norbs007 Posted November 11, 2005 Share Posted November 11, 2005 Dude, fitted Bar-Sto barrel...no substitute. Custom Glock Racing Link to comment Share on other sites More sharing options...
andrewcolglazier Posted November 11, 2005 Share Posted November 11, 2005 I have Barsto barrels in My G21 and my G17. Both will shoot sub-2" groups at 25 yards with decent handloads off a rest. I also have a G24 with a stock barrel. It will also shoot sub-2" groups off a rest. Do I think the aftermarket barrels are worth the expense? Yes, as they allow me to shoot handloads using non-jacketed bullets without concern, and because they add a modicum of accuracy in over-all grouping, adding cutting 1-3" from all groups. However, the main thing all three pistols share, which I believe has contributed more to the accuracy of the pistols than the barrels, is that all three have precision slide locks installed. They greatly improve lockup, and they are much cheaper than new barrels. Andy C. Thanks of the input. The consensus seems to be that I'd be wasting my money. Apparently no one saw a major accuracy increase using a pre-fitted barrel. Guess I'll spend the $100+ somewhere else. Link to comment Share on other sites More sharing options...
Clay1 Posted November 11, 2005 Share Posted November 11, 2005 "all three have precision slide locks installed." What is a precision slide lock? Do you have a link with a picture or description? Never heard of one. Thanks Link to comment Share on other sites More sharing options...
cautery Posted November 11, 2005 Share Posted November 11, 2005 "all three have precision slide locks installed." What is a precision slide lock? Do you have a link with a picture or description? Never heard of one. Thanks +1 Me either. Link to comment Share on other sites More sharing options...
Clay1 Posted November 11, 2005 Share Posted November 11, 2005 Thanks for joining in there Clay A. I don't mind asking questions. I thought that I knew a thing or two about Glocks. I have two G34s one set up for Production/SSP and one set up for Limited/ESP. I'll admitt when I don't know something, but am curious to learn. Link to comment Share on other sites More sharing options...
SRT Driver Posted November 11, 2005 Share Posted November 11, 2005 The slide lock/takedown lever is the little thing you pull down to remove the slide. The barrel makes contact with it and it keeps the barrel/slide from moving forward. There are a couple of mfgrs that make oversized slidestops/takedown levers. Actually, some just find a stock one that locks the barrel up tight and trial fit until one is acceptable. Link to comment Share on other sites More sharing options...
Clay1 Posted November 11, 2005 Share Posted November 11, 2005 Thanks SRT for the reply. If you look at this graphic: http://www.topglock.com/info/partgraphic.htm you are talking about part number 21, which the graphic refers to as a "slide lock". So who makes a precision one and is it Production legal? Thanks Rick Link to comment Share on other sites More sharing options...
jkrispies Posted November 12, 2005 Share Posted November 12, 2005 Hhmmm... I this oversized slidelock concept. Since it's such a simple part, I'm also thinking that you DON'T need a custom barrel to make use of it, either? Anybody have a price and place where I can find one for my stock G17? Link to comment Share on other sites More sharing options...
Newguy Posted November 12, 2005 Author Share Posted November 12, 2005 T.R. Graham is having some slide locks made that will be ready within the next couple of months or so. You can reach im at Ph. 678-517-0988 or grhm458@cs.com Link to comment Share on other sites More sharing options...
jkrispies Posted November 12, 2005 Share Posted November 12, 2005 T.R. Graham is having some slide locks made that will be ready within the next couple of months or so. You can reach im at Ph. 678-517-0988 or grhm458@cs.com I have a feeling that T.R. Graham is going to have a pleasant surprise when he checks his email on Monday! Link to comment Share on other sites More sharing options...
SRT Driver Posted November 12, 2005 Share Posted November 12, 2005 Clay, Yup, that's it. Brownells has one also. But they do look different than the stock part (they stick out a little farther) so the Production legality might be an issue. I'd run the Production legality issue by John Amidon before I'd put it on a Production gun. Link to comment Share on other sites More sharing options...
Newguy Posted November 12, 2005 Author Share Posted November 12, 2005 T.R. Graham showed me one of his slide locks at a gunshow. As much as I begged, he wouldn't sell me the only one he had left. IIRC, T.R. explained that it wasn't that the slide lock was extended, but that the groove in his was narrower than the Glock part and was straight/true. T.R. gave me an old Glock slide lock he had lying around he knew was straight. Although the lockup on my original barrel was still sloppy, it was about 50% tighter. I suspect the barrel fit would be even tighter if I had a properly fit slide lock. Link to comment Share on other sites More sharing options...
Flexmoney Posted November 12, 2005 Share Posted November 12, 2005 Somebody did a write-up on these (Robin Taylor in Front sigyht??). As with other things Glock...most guns already had a good fit and showed no difference with the new part. Others (not as well fit), show a slight increase in accuracy (12% comes to mind). (There has got to be a thread or ten on these on GT.) Link to comment Share on other sites More sharing options...
andrewcolglazier Posted November 12, 2005 Share Posted November 12, 2005 (edited) Sorry it has taken me so long to get back to this thread..... I got all of my precision slide locks from TR. IMO, they are worth the money, which is substantially less than an aftermarket barrel. They are dimensionally exactly the same as the stock part, however, the little serrations that your fingers touch when taking down the pistol are much sharper, and easier to hold on to. Looking at the weapon, you can see no difference. As far as a difference in accuracy; it has been a while since I did side-by-side comparisons, but working from memory, I experienced at least a 2" shrinkage (ha! I said "shrinkage"!) in group size at 25 yards, independant of the aftermarket barrels, in both my 21 and my 17. You do not need an aftermarket barrel to make use of this part. Andy C Somebody did a write-up on these (Robin Taylor in Front sigyht??). As with other things Glock...most guns already had a good fit and showed no difference with the new part. Others (not as well fit), show a slight increase in accuracy (12% comes to mind). (There has got to be a thread or ten on these on GT.) Edited November 12, 2005 by andrewcolglazier Link to comment Share on other sites More sharing options...
vluc Posted November 13, 2005 Share Posted November 13, 2005 But are they production legal? Probably not. Link to comment Share on other sites More sharing options...
atmar Posted November 13, 2005 Share Posted November 13, 2005 (There has got to be a thread or ten on these on GT.) i did a search on "precision slide locks" in the general glocking section and came up empty. Link to comment Share on other sites More sharing options...
jkrispies Posted November 13, 2005 Share Posted November 13, 2005 (There has got to be a thread or ten on these on GT.) i did a search on "precision slide locks" in the general glocking section and came up empty. I Googled it and came up dry, too. Same thing with Brownells online, but then I can never get anywhere with their search engine. Link to comment Share on other sites More sharing options...
jkrispies Posted December 1, 2005 Share Posted December 1, 2005 T.R. Graham is having some slide locks made that will be ready within the next couple of months or so. You can reach im at Ph. 678-517-0988 or grhm458@cs.com Was anybody able to get ahold of Mr. Graham via email? Two weeks and nary a reply on my end... Link to comment Share on other sites More sharing options...
RifleShooter Posted June 25, 2006 Share Posted June 25, 2006 Sorry it has taken me so long to get back to this thread..... I got all of my precision slide locks from TR. IMO, they are worth the money, which is substantially less than an aftermarket barrel.They are dimensionally exactly the same as the stock part, however, the little serrations that your fingers touch when taking down the pistol are much sharper, and easier to hold on to. Looking at the weapon, you can see no difference. As far as a difference in accuracy; it has been a while since I did side-by-side comparisons, but working from memory, I experienced at least a 2" shrinkage (ha! I said "shrinkage"!) in group size at 25 yards, independant of the aftermarket barrels, in both my 21 and my 17. You do not need an aftermarket barrel to make use of this part. Andy C Somebody did a write-up on these (Robin Taylor in Front sigyht??). As with other things Glock...most guns already had a good fit and showed no difference with the new part. Others (not as well fit), show a slight increase in accuracy (12% comes to mind). (There has got to be a thread or ten on these on GT.) http://www.glocktalk.com/showthread.php?s=...mp;pagenumber=1 It would appear that many people have seen good results with this 'precision slide lock'. I'm planning to order one for my Glock 19. They are available from The Glock Guy. Arnie Link to comment Share on other sites More sharing options...
Harmon Posted June 26, 2006 Share Posted June 26, 2006 worth it in a 40, 100 percent in a 9mm, i would suggest swithcing ammo before ta barrel change WWB ammo is good, but its not known for super accuracy..in my 9mm carbine, No ball ammo shot as good as some of my JHP handloads with accurate arms number 7 Link to comment Share on other sites More sharing options...
atmar Posted June 26, 2006 Share Posted June 26, 2006 has anybody tried the TR graham slidelock on a gun w/ a semi drop-in barsto????? Link to comment Share on other sites More sharing options...
Damn_Bastard Posted June 26, 2006 Share Posted June 26, 2006 I like to sacrifice a chicken, and smear some of the blood around under my hairline, and into my armpits. I always make sure to carry 3 quarters in my right hand pocket, all from no later than 1974... Guys.... The slide lock stops the barrel going forward, where it has long been in planar contact with the locking block, holding it up, hard against the inside top of the slide. The accuracy of the fit is between the locking block and the barrel, the front of the ejection port cut and the corresponding spot on the barrel, and the breechface cut and that lug above the chamber. "straight and true"?? who cares? It can pivot, it's spring retained, and it's sitting in a plastic channel! There is an upper limit to the dimensional tolerances of an injection molding and they are far looser than can create the effects you're describing. All it could (it doesn't, but if it could) affect is the front/rear positional repeatability of the fit, which would create angular changes proportional to the surface finish irregularity of the barrel, locking block and inside top of the slide (which are ncie and smooth, especially on a broken in gun). And since the running fit type clearance is larger (of necessity) than the finish spec, what you're describing is impossible. We're talking about angular changes in the micron (millionth of a meter) over the ~110 mm length of the barrel. No discernable effect. Moreover, these angular changes are many orders of magnitude smaller than than provided by the required clearances for operation. Simplest explaination: Psychological effect. Save your money. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now