CarRacer Posted November 21, 2013 Share Posted November 21, 2013 I always see polishing parts as a way to ensure reliability but what tools are used to get this done? I know a dremel or a wheel for a bench grinder are options. What's the best way to accomplish occasionally needing to polish gun parts? Thanks for any info, James Link to comment Share on other sites More sharing options...
Waterfowl-widowmaker Posted November 21, 2013 Share Posted November 21, 2013 I use a variable speed dremel on the slowest setting. Link to comment Share on other sites More sharing options...
Guest Posted November 21, 2013 Share Posted November 21, 2013 cratex bars, ceramic/india/hard arkansas stones, and smooth cut files are what I have used. If you got some time go to Brownells.com look around at what they have. It's always fun just to look through their catalog. Link to comment Share on other sites More sharing options...
StraightUp_OG Posted November 21, 2013 Share Posted November 21, 2013 All that has been said and to add 600-1200 or finer wet/dry sandpaper. Link to comment Share on other sites More sharing options...
CarRacer Posted November 21, 2013 Author Share Posted November 21, 2013 I've never wet sanded before, I'll have to read up on that. What about using polishing compounds? I haven't used those either. I'm mostly familiar with using air tools from working on cars, quite the different animal than guns. Link to comment Share on other sites More sharing options...
ltdmstr Posted November 21, 2013 Share Posted November 21, 2013 (edited) 600+ wet and dry sandpaper on a piece of plate glass works good for flat surfaces. For irregular shapes like a barrel feed ramp, start with a craytex bit on the dremel then go to a felt wheel with semichrome polish. That will give you a mirror finish. For polishing with dremel I find high speed works better. Edited November 21, 2013 by ltdmstr Link to comment Share on other sites More sharing options...
Jediwarrior Posted November 21, 2013 Share Posted November 21, 2013 Craytex, 600-1200 fine sandpaper, and felt cones/cylinders with polishing compound. You can buy Craytex polishing cones/cylinders, and felt cones/cylinders from Otto Frei. Don't forget the matching mandrels. Polishing compounds from Brownells. Link to comment Share on other sites More sharing options...
kneelingatlas Posted November 21, 2013 Share Posted November 21, 2013 It auto parts store sells foamy 3000 grit sand paper which is great for finishing off the hammer hooks and such. Link to comment Share on other sites More sharing options...
Bob DuBois Posted November 21, 2013 Share Posted November 21, 2013 I like a fine paper also, usually put a little light oil or Kerosene from the parts washer. Glass is a good idea for larger flat surfaces. Small parts I have a metal block or the Drill press table. Simichrome on a terry cloth rag for fine hand polish, wheel with polishing compounds. Be careful with a wheel as you can round surfaces that you didn't intend to. A cut up old belt works good in a vice to hold parts if your hand polishing. Use a six inch long 1/8th drill rod in a Dremel with a strip of paper to polish inside frames, mag wells, inside slides etc. Change the paper for a large patch with compound to finish. Don't rush a project, A Dremel can ruin a part as fast as it can fix it. Harder to put metal back that take it off. Link to comment Share on other sites More sharing options...
kneelingatlas Posted November 21, 2013 Share Posted November 21, 2013 Harder to put metal back that take it off. :cheers: You can't hear this enough times! Link to comment Share on other sites More sharing options...
Powder Finger Posted November 21, 2013 Share Posted November 21, 2013 you can also get a fairly inexpensive jewlery type mini grinder that takes like 3-4 inch cratex and polishing wheels (cloth type). they have tapered spindles so you can change wheels fast. Link to comment Share on other sites More sharing options...
factorysponsered Posted November 21, 2013 Share Posted November 21, 2013 I start with 800grit sand paper and more to 1000,2000, and 3000. After gettin a nice polish on what ever your working on, 3000 is all you need to bring it back. Link to comment Share on other sites More sharing options...
Knp1288 Posted November 22, 2013 Share Posted November 22, 2013 How do you know when to move to a finer sandpaper? Eg 800 grit, then 1200 grit then 2000 grit Link to comment Share on other sites More sharing options...
factorysponsered Posted November 22, 2013 Share Posted November 22, 2013 Its not that hard, pay around with scrap material to get a feel for it Link to comment Share on other sites More sharing options...
practical_man Posted November 23, 2013 Share Posted November 23, 2013 How do you know when to move to a finer sandpaper? Eg 800 grit, then 1200 grit then 2000 grit How do you know when to move to a finer sandpaper? Eg 800 grit, then 1200 grit then 2000 grit Sand in one direction with coarser grit. Sand 90 degrees to that direction with next finer paper. When all the scratch marks from the first paper are gone go to finer paper, rotate part so you can see when coarser scratches are out. Continue till you are happy with the result. With some practice you will know when to change grits by how the part looks under strong light. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now