SecretNY Posted June 16, 2013 Share Posted June 16, 2013 Was able to get (with help of a friend) a new Stock II. Switching over from a Glock 34, what do you guys recommend is the next step in making it a comp gun? I've ordered both the Blade Tech and Ghost holsters and picked up some new mags. Arik Link to comment Share on other sites More sharing options...
BiggMike Posted June 16, 2013 Share Posted June 16, 2013 Was able to get (with help of a friend) a new Stock II. Switching over from a Glock 34, what do you guys recommend is the next step in making it a comp gun? I've ordered both the Blade Tech and Ghost holsters and picked up some new mags. Arik Where did you order your Ghost holster from? Link to comment Share on other sites More sharing options...
kneelingatlas Posted June 16, 2013 Share Posted June 16, 2013 (edited) Polish, polish, polish! Hammer hooks, sear, disconnector hooks, trigger bar, most important of all the trigger plunger: the shaft and the head (...that doesn't sound right...) You could also use a reduced power trigger return spring, trigger plunger spring and hammer spring. Edited June 16, 2013 by kneelingatlas Link to comment Share on other sites More sharing options...
Mo Hepworth Posted June 16, 2013 Share Posted June 16, 2013 Polish, polish, polish! Hammer hooks, sear, disconnector hooks, trigger bar, most important of all the trigger plunger: the shaft and the head (...that doesn't sound right...) You could also use a reduced power trigger return spring, trigger plunger spring and hammer spring. don't forget the sear cage at the back angles...the trigger bar goes down off this Link to comment Share on other sites More sharing options...
SecretNY Posted June 17, 2013 Author Share Posted June 17, 2013 I'm a pretty handy around a Glock but not sure how I'd handle the Stock II. Is it worth it to send it to one of the Tanfoglio smiths around? Mike, PM me for the place I got the holster from. Thanks guys. Link to comment Share on other sites More sharing options...
ogiebb Posted June 17, 2013 Share Posted June 17, 2013 Got mine here http://www.ipsc.org/store/store.htm Link to comment Share on other sites More sharing options...
Wilfred Posted June 19, 2013 Share Posted June 19, 2013 (edited) Which one is for the Stock II? There's only Stock and Stock III. Edited June 19, 2013 by Wilfred Link to comment Share on other sites More sharing options...
ogiebb Posted June 19, 2013 Share Posted June 19, 2013 Order the "Tanfoglio" model.. its for the Stock 2, Tanfoglio III refers to Stock 3 Link to comment Share on other sites More sharing options...
ogiebb Posted June 19, 2013 Share Posted June 19, 2013 Which one is for the Stock II? There's only Stock and Stock III. Order the "Tanfoglio" model.. its for the Stock 2, Tanfoglio III refers to Stock 3 Link to comment Share on other sites More sharing options...
rebsimeanblackbears Posted June 19, 2013 Share Posted June 19, 2013 How has the Stinger held up? I've read some complaints that it works itself loose after you get it adjusted and that some of the screws stripped out relatively easily when you tried to keep it from coming loose. Link to comment Share on other sites More sharing options...
Torogi Posted June 19, 2013 Share Posted June 19, 2013 I have a Stinger and the first one I got (from IPSC store mentioned above), the fit wasnt perfect. every draw the front sight is being shaved on the top left corner. Tried to relieve some material inside (no problem with the screws though) but to no avail. I contacted Ghost, they said they will replace it for free but through the store i bought it from, not directly from them. Took a little while but the replacement is much better fit. Link to comment Share on other sites More sharing options...
Big Dog Howie Posted June 20, 2013 Share Posted June 20, 2013 (edited) On a side note I just received 6 new 10 rnd mags large frame( they will ask you for the serial # so they can verify its a large frame) from EAA took less than a week 3 for $75 and they are the new Mec gar anti friction finsh with black followers. I loaded up 10 of my dummy rnds(made these for reload practice,marked with a big D in red for dummy no primer no powder)hand cycled with out any issues in my Stock II All ready to run production,oh wait still need holster after seeing that you had problems with the stinger I may just stay with the Blade tech DOH. Edited June 20, 2013 by Big Dog Howie Link to comment Share on other sites More sharing options...
ogiebb Posted June 20, 2013 Share Posted June 20, 2013 I think the issue with the stinger holster has been resolved. my stingers for my Stock 2 and Stock 3 has enough clearance for a .180 front sight... Link to comment Share on other sites More sharing options...
Big Dog Howie Posted June 20, 2013 Share Posted June 20, 2013 Ok any other issues,I do like the way it sits it gives more room for your hand to grip the pistol better Link to comment Share on other sites More sharing options...
SecretNY Posted June 20, 2013 Author Share Posted June 20, 2013 Hey will this front sight work with the Stock II? http://www.dawsonprecision.com/ProductDetail.jsp?LISTID=80001425-1333572490 Link to comment Share on other sites More sharing options...
Torogi Posted June 20, 2013 Share Posted June 20, 2013 I installed 019-118. Fits fine, DP EAA Witness Match Fiber Optic Inserted Front Sight .160 Tall x .100 Wide with Factory Adj Rear #019118 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now