IuniusBrutus Posted February 25, 2012 Share Posted February 25, 2012 I've been shooting IDPA a while, and would like to start shooting USPSA with my CZ SP-01. Only problem is, it is a DA/SA gun with a manual safety. Since I have to start hammer down, this would mean I would have to lower the hammer on a hot chamber by hand. While this isn't exactly what I would like to do, I would not be too bothered by it. I'm more concerned about the RO being bothered...while the pistol would obviously be pointed down range during this, I can understand how it could cause concern. My question: Am I being too worried about this? Is it common? Or while ROs typically not allow it? Link to comment Share on other sites More sharing options...
Chuck Anderson Posted February 25, 2012 Share Posted February 25, 2012 Very common to see. Almost every CZ shooter does it. Just take your time and pay attention and you'll be fine. Link to comment Share on other sites More sharing options...
Sarge Posted February 25, 2012 Share Posted February 25, 2012 My question: Am I being too worried about this? Is it common? Or while ROs typically not allow it? It must be done so RO's have no say. Like Chuck said practice it until there is no doubt you can safely do it. Link to comment Share on other sites More sharing options...
Skydiver Posted February 25, 2012 Share Posted February 25, 2012 It's very common. In case an RO threatens to DQ you for having a finger in the trigger guard while loading, refer them to: 10.5.9 Failure to keep the finger outside the trigger guard during loading, reloading, or unloading. Exception: while complying with the “Make Ready” command to lower the hammer of a gun without a decocking lever, or while initially loading a revolver with a spurless hammer. Link to comment Share on other sites More sharing options...
CZinSC Posted February 25, 2012 Share Posted February 25, 2012 It's more common than you think. It's no big deal. Just remember, Pull hammer back, then pull trigger, then lower hammer. And if an RO gives you a hard time, politely quote the rule Skydiver quotes above. If they still argue with you, call for the CRO. And if he agrees with the RO, call for the RM. I doubt that will happen, but know your options. Especially when you are right! Link to comment Share on other sites More sharing options...
jdphotoguy Posted February 25, 2012 Share Posted February 25, 2012 That is a very popular gun in the sport, I know several just at my range, so I doubt you will have an issue Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted February 25, 2012 Share Posted February 25, 2012 Am I too worried about this? It must be done so RO's have no say. practice it until you can safely do it. +1. Practice it WITH AN UNLOADED GUN. Pointed safely. Good luck. Jack Link to comment Share on other sites More sharing options...
IuniusBrutus Posted February 26, 2012 Author Share Posted February 26, 2012 Alright, that's what I wanted to hear - thanks! Link to comment Share on other sites More sharing options...
bikerburgess Posted February 27, 2012 Share Posted February 27, 2012 Not a big deal, I have had 1 RO ask me about it on a polimer witness (i think he was surprised that a black plastic gun needed decocked more than anything else)I even made my 14yr old start in USPSA manualy decocking a Witness. Mike Link to comment Share on other sites More sharing options...
gunguru Posted February 27, 2012 Share Posted February 27, 2012 But remember to grasp your hammer with 2 finger, thumb and index, and not just rely on your thumb, too much chance to let him slip... Link to comment Share on other sites More sharing options...
DonovanM Posted February 28, 2012 Share Posted February 28, 2012 Also be sure you're pointing your gun at the berm when you do it, just like when dry firing after ULSC. If it does go off, that's where you want it to go. Link to comment Share on other sites More sharing options...
bikerburgess Posted March 5, 2012 Share Posted March 5, 2012 But remember to grasp your hammer with 2 finger, thumb and index, and not just rely on your thumb, too much chance to let him slip... I like to put the pad of my thumb on the front of the hammer (part that hits firing pin) lift the hammer off the sear, pull trigger and then lower hammer till thumb is pinched between hamer and slide then roll thumb out from between hammer and slide. Mike Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now