Jump to content
Brian Enos's Forums... Maku mozo!

tedahlenius85

Classified
  • Content Count

    137
  • Joined

  • Last visited

About tedahlenius85

  • Rank
    Finally read the FAQs
  • Birthday 05/05/1985

Profile Information

  • Gender
    Male
  • Location
    Europe
  • Real Name
    Ted Åhlenius

Recent Profile Visitors

564 profile views
  1. A little tip regarding extractor springs. Instead of buying a xtra power one, you can also cut a few coils off a mag button spring an put it inside the stock extractor one. Double spring so to speak. Works great for adding extra power.
  2. Hello, in what angle should the slide be mille on a Tanfo for red dot? 89’ or even closer to 90’? What is the downside of going parallell with the top of slide?
  3. I’d say 99.5% [emoji846] Skickat från min iPhone med Tapatalk
  4. Carl, is the fp pin in use after this cut? If so, can you post a photo of it to see how much they needed to cut off it? Skickat från min iPhone med Tapatalk
  5. Try Roughneck or Full checkered instead of bogies if you havent already. They are comfortable but still grippy.
  6. Yes, its a timing issue. But I cant figure out how to tune the disco to make this work. If pulling the trigger normally, you never notice it. You really have to pull it and hold it precisely where hammer drops to make it drop to half cock. Skickat från min iPhone med Tapatalk
  7. Hi, how to fix a shadow that during double action drops to half cock before pulling a little litle bit more and it falls entirely? Pre-b disco and comp hammer.
  8. Also got inconsistent powder drops with Evo. The powder measure have been back to M7 for an update. I get about 0.3 gr variations. When manually handcycle the drop, its consistent more or less, but when running the press, its up to 0.3gr lower drop. I have tested lowest speed setting, higher speed, bottom dwell up to 10, index speed and so.. it doesnt matter. Something happens differently that causes this. Might be how the funnel lining up as someone wrote or just that when funnel activates the rotation and drop, some powder ”jumps” up and the space for powder isnt packed full when rotation to release it. I dont know, but it sucks big time. I have to buy a Dillon powder measure now to use until I hear something about M7 fixing the problem. I didnt realize the drops were so inconsistent until I chrono ammo and saw 70-100fps ES and 30 SD. With my old press I had always single digit SD. The accuracy was crap too with loads from Evo which isnt strange with those kind of variations in powder and fps. I also had the powder drop get stuck in its upper position. So it didnt rotate back to pick up new powder. This resulting in lot of empty cases since I dont have a powder check to stop machine.
  9. It is .092” high. Which is in the higher range of the specs they recommend (.060-.100) Skickat från min iPhone med Tapatalk
  10. I took it apart and made sure everything ran smooth and was clean. It seems like with more speed, the index thing moves cause of more torque from machine. Making it not grab the shellplate sometimes. Instead slips underneath it or something. Skickat från min iPhone med Tapatalk
  11. Anyone have experienced indexing problems with shellplate? I followed the index adjustment instructions and everything was within specs. Still skips indexing every 5 or so strokes while running the press on 1600+ rph. If someone had the same problem and figured it out I appreciate the help. Am waiting response from support about it, but someone might be faster with answer here maybe?
  12. http://traffic.libsyn.com/skyttepodden/Skyttepodden20-20Ben20Stoeger.mp3 Ben talks about training, shooting when juiced up and where to buy the Worlds best sushi.
  13. https://www.ipscstore.com/en/thunder-stinger/952-ghost-holster-body-distance-plate-2000000009520.html?search_query=Ghost&results=120
  14. 0.2gr is not ok with any powder. 0.05-0.1gr is ok. Skickat från min iPhone med Tapatalk
×
×
  • Create New...