Jump to content
Brian Enos's Forums... Maku mozo!

kk4364

Classifieds
  • Content Count

    344
  • Joined

  • Last visited

Everything posted by kk4364

  1. I have never heard a negative review, or negative anything about Gans. That being said if I ever wanted a slide cut or any other custom work I would give him a call or email. Sent from my SM-G975U using Tapatalk
  2. Fastenal look them up online, I've worked in the automotive dealership world for a while. They have, or can get about anything. Sent from my SM-G975U using Tapatalk
  3. Jb weld or some hard 2 part epoxy, something you can shape after it hardens. Sent from my SM-G975U using Tapatalk
  4. Or take it apart and add material to the "ball" portion that it locks onto, making it snug with less torquing. Sent from my SM-G975U using Tapatalk
  5. His was fit better than mine. Sent from my SM-G975U using Tapatalk
  6. Looks like a fitted Nitro Fin. Sent from my SM-G975U using Tapatalk
  7. Infinity wide left ambi, with Nitro Fin. Sent from my SM-G975U using Tapatalk
  8. Here is my old limited gun with Nitro Fin and Lonestar Innovations tactical wide ambi safety. Sent from my SM-G975U using Tapatalk
  9. Tha1000 agreed! I installed another one on my stainless Limcat grip, awesome! Sent from my SM-G975U using Tapatalk
  10. Evenly is the hard part! Sent from my SM-G975U using Tapatalk
  11. I would use fine grade sand paper by hand. Hopefully someone with more knowledge than me will chime in. Sent from my SM-G975U using Tapatalk
  12. If it is riding the lower lugs or starting uneven I believe so. I am not a Smith just trying to share what I have had to do in the past. Sent from my SM-G975U using Tapatalk
  13. I would check the pin diameter and compare to original. If the pins are like in diameter I would use dykem to try to pinpoint further. Sent from my SM-G975U using Tapatalk
  14. Your ADE red dot should have the same mounting pattern as Burris ff3. Sent from my SM-G975U using Tapatalk
  15. I've never used Cr speed bit see a bunch of people use them. Sent from my SM-G950U using Tapatalk
  16. Daa racers are what I use, they are adjustable, and you can run bullets out. I prefer bullets out and have not had any issues for about 2 years. They are installed on a Daa belt as well and fit perfect, nice and tight. Sent from my SM-G950U using Tapatalk
  17. No problem! Sent from my SM-G950U using Tapatalk
  18. Gotcha, thanks Sent from my SM-G950U using Tapatalk
  19. Did that help? Sent from my SM-G950U using Tapatalk
  20. How did you go about getting this grip? If you dont mind me asking. Sent from my SM-G950U using Tapatalk
  21. Also this is where you would apply marker or dykem to see where the safety detent makes contact. Then you can settle on the position of detent. Sent from my SM-G950U using Tapatalk
  22. This ended up being ok, but should of gone a tiny bit higher Sent from my SM-G950U using Tapatalk
  23. It's going to be different on each gun because of slight dimensional differences f re om manufacturer. Sent from my SM-G950U using Tapatalk
  24. If you mark the contact area that the safety detent meets with nitro fin , marker, or dykem. And install you can move the nitro fin into place a few times and the mark that it makes should be the spot. Does that make since? Sent from my SM-G950U using Tapatalk
  25. True Sent from my SM-G950U using Tapatalk
×
×
  • Create New...