Kurusty

Correct, they are all in the “N” frame family

I believe that they are 6-48 x .312 length is dependent on mount, ensure that screw doesn’t go past the inside of the top strap

Lmfao! Truth

Speed Bees

Why not just do a dovetail cut and tap so that you can buy sights that fit CZ and Tanfoglio? Easier to machine and you can buy front rights for them?

I just ordered one from Bowen in October, it took a couple of weeks to get because I believe that they build to order. I don’t like machining small parts and $45 is well worth it

I can’t tell you the thickness of the top of my head, but it’sa super fine that I’ve had for years. Basically, I’m to lazy to go into the garage, AKA furnace.

If the trigger pull is constant and smooth you should be good. The last one that I did, I stoned it without removing the sear, but I only had to take a couple of passes.

Doesn’t matter which side you drive the pin out, but I don’t recommend pushing it all of the way, just enough to remove the sear. It looks like you’ve installed it, is it not smooth enough?

Is the firing pin and spring new? Could be worn out..

if it cuts, the finish will be removed. Check 4drentals.com , they rent reamers, I’ve used them a couple of times for odd calibers. Your best bet is to have a gunsmith do it, it will probably cost you the same as the rental.

Is it a titanium cylinder?

You might be lucky enough to have cylinders that are actually at .3575”. If you’re not having any accuracy problems, don’t worry about it. The bullet shouldn’t just push through, it should take a couple of light taps with a hammer and a dowel pin.

I used them exclusively in my 610 for a full year of competition, never had a problem.

Sure that it’s not a V-Comp? They are 627-5’s also

Hogue are pretty darn good. https://www.hogueinc.com/competition/ammo-holders/holdall-universal-speed-loader-holder-black-pack-of-four

I’m lucky enough to live in a state where there’s a match every weekend, ICORE 3 matches a month, 2 steel challenge a month, USPSA pretty much every weekend and some week nights. I do like to mix it up, but I do believe that shooting is shooting no matter what platform you choose. I love revolver and have been shooting more ICORE than USPSA. I actually shot my open revo in open Class at 4 USPSA matches to get more practice in before the state and SW regionals. I know that I didn’t have any chance of placing well, but I didn’t care because I wanted the trigger time. I’d love to shoot revo in USPSA, but like most people my eyes aren’t getting any better.

I have a 21” barrel on order with Odin Works alone with their Atlas comp. It’s on back order, but I’m in no hurry. I haven’t picked an upper yet, but I’m going to buy another Spikes lower to put it on. I’ve been shooting Grendel for a couple of years and when they announced this round, I was sold! Especially since I use the same projectile in my 6mm Creedmore.

If you system has the Techlock clips you can use the spacers. I can’t take pictures of it now, but I will when I get home.

I use north mountain moon clip holder with 1” aluminum spacers that I bought from McMaster-Carr. Buy them longer than you think you need and cut them to length. I both the .166 diameter through hole because my screws are 8-32 threads.

Apex for extractor, do that first because the ejector is stamped sheet metal so it’s harder to change the contract angle.

Have you tried to change the profile of your ejector yet? If you have a lot of rounds through it, you might want to change the extractor and spring also.

I just put mine on a digital mount on a CZ75 and don’t have any issues. I put around 2K on the M&P before this. The few people that I shoot with have no issues either.

Not on mine, but I took the sights off since I only use it for competition