JFlowers Posted April 22, 2008 Share Posted April 22, 2008 I'm having a problem with my 550 and I am betting someone here has experienced it before. If not I will call Dillon support. My 550 sticks just at the top of the upstroke. Basically when the head of the primer arm is slotting into the opening on the table. I have cleaned everything trying to make sure that its just not a buildup of gunk, but that did not seem to resolve the problem. Any thoughts? Not that it matter but the press is setup for 38 super with small primers and all. Link to comment Share on other sites More sharing options...
Flatland Shooter Posted April 22, 2008 Share Posted April 22, 2008 To make sure the problem is in the ram, pull the die holder out of the press and see if it still does it. On 9mm I set the dies as low as possible to resize as much of the brass as possible and sometimes see this. Bill Link to comment Share on other sites More sharing options...
lynn jones Posted April 22, 2008 Share Posted April 22, 2008 check for cracks in the pivot arms on each side of the center shaft. lynn Link to comment Share on other sites More sharing options...
benos Posted April 24, 2008 Share Posted April 24, 2008 By trying it without the Toolhead (as was suggested), and also trying it without the priming operating rod, you should be able to isolate where the problem is. be Link to comment Share on other sites More sharing options...
Larry Burchfield Posted April 24, 2008 Share Posted April 24, 2008 My 550 used to give the feeling of sticking because the sizing die was set to low or sometimes if using a taper crimp and applying a heavy crimp. Larry Link to comment Share on other sites More sharing options...
lynn jones Posted April 24, 2008 Share Posted April 24, 2008 well, what did you find out? lynn Link to comment Share on other sites More sharing options...
JFlowers Posted April 24, 2008 Author Share Posted April 24, 2008 The problem is happening when the head of the primer arm passes through the head of the ram/shellplate. Working on trying to diagnose it further. Unfortunately, work (the kind that pays the bills) keeps eating into my time! Thanks everyone for their help! Link to comment Share on other sites More sharing options...
benos Posted April 24, 2008 Share Posted April 24, 2008 Sounds like definitely an alignment issue. Gary (dillon) should have something for you on that. In the meantime, here's a couple sentences from my 550 priming notes: Be sure both screws (14530) that tighten Roller Bracket Shell Platform (14280) from bottom (to the Shellplate Platform) are tight! Make sure Priming Seating Punch Assembly is fully bottomed out before tightening screw (13996): Measured from bottom of Primer Slide (13920) to top of seated Primer Seating Cup (13284/5), dimension should be between 2.125 - 2.220 inches. be Link to comment Share on other sites More sharing options...
dillon Posted April 24, 2008 Share Posted April 24, 2008 There is an adjustment bolt with a jam nut on it protruding from the rear of the primer feed base. The upper part of the pin pressed through the primer slide (the return spring attaches to the lower part of this pin) contacts the head of this screw, stopping forward travel. easiest way to adjust is to loosen the jam nut a few turns, thread this bolt into the primer housing with your fingers a few turns. Manually guide the primer cup up into the platform and have the handle all the way up. Now, back the screw out with your fingers until it just contacts the pin. Pull the machine handle down, use an Allen wrench to keep this scrw in the same position, and use a small wrench to snug the jam nut. Shazzamm!! You are once again realigned. Please pay the chiropractor at the window on your way out Link to comment Share on other sites More sharing options...
JFlowers Posted April 25, 2008 Author Share Posted April 25, 2008 Well, since I don't work on Fridays I finally got to spend some time dealing with this issue. And DILLON had it right. The Primer Arm was just slightly out of adjustment, so the Primer Head was rubbing against the side of the primer opening. A tweak of the adjustment screw and things are running well again. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now