IHAVEGAS Posted June 16, 2019 Share Posted June 16, 2019 (edited) Maybe 20,000 ish rounds on the gun, and original followers and springs in all mags. Anybody else had the issue come up over time and then fixed it? Slide closes without operation of the slide release on insertion of the mag, but apparently a bit too soon. Edited June 16, 2019 by IHAVEGAS Link to comment Share on other sites More sharing options...
Polymer Posted June 16, 2019 Share Posted June 16, 2019 You say slide closes to soon: Check the part of slide stop that contacts notch in slide to see if it's worn/rounded. Check the slide notch that contacts slide stop. Make sure follower is pushing slide stop all the way up. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted June 17, 2019 Author Share Posted June 17, 2019 Noticed a bit of rounding here, may explain the issue, filed it to square the edge after taking the photo. Slide shows no wear pattern so it looks like Tanfo did the smart thing and made the slide harder than the slide stop. Link to comment Share on other sites More sharing options...
johnbu Posted June 18, 2019 Share Posted June 18, 2019 It sounds like the notch in the slide is rounded over so the slide slips off the release too easily. Just a guess. Link to comment Share on other sites More sharing options...
himurax13 Posted June 18, 2019 Share Posted June 18, 2019 Have you tried installing +10% magazine springs? 20k rounds sounds like enough cycles on the springs to warrant replacement. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted June 18, 2019 Author Share Posted June 18, 2019 11 hours ago, johnbu said: It sounds like the notch in the slide is rounded over so the slide slips off the release too easily. Just a guess. 48 minutes ago, himurax13 said: Have you tried installing +10% magazine springs? 20k rounds sounds like enough cycles on the springs to warrant replacement. Good thoughts. I'm going to see what resquaring the slide stop did & then proceed from there if needed. For what it is worth, the slide does not appear rounded or otherwise show signs of being worn at the area of contact, the mags appear to lift the slide stop fully so that makes me less suspicious of spring/follower wear being in play. Link to comment Share on other sites More sharing options...
himurax13 Posted June 18, 2019 Share Posted June 18, 2019 (edited) Well the round not getting picked up concerns me. That leads me to believe there is an issue with the magazines. The slide going into battery after inserting a mag does not since most of my pistols do that. Sometimes I round off my slide stops on purpose, LOL. Edited June 18, 2019 by himurax13 Link to comment Share on other sites More sharing options...
Polymer Posted June 18, 2019 Share Posted June 18, 2019 (edited) Round not getting picked up....See if it does it on same mag loaded to 10 rounds vs loaded to 17 rounds. This will tell you if it's spring issue or not. Edited June 18, 2019 by Polymer Link to comment Share on other sites More sharing options...
IHAVEGAS Posted July 23, 2019 Author Share Posted July 23, 2019 https://benstoegerproshop.com/bsps-magazine-floor-plates-base-plates/ This one is really irritating. Can not duplicate the problem away from a match, no matter how I try to slam the mag in or whatever, maybe it is temperature related. Squaring off the old slide stop did not help. New slide stop on order as well as new baseplates. I'm going to keep the old baseplates attached to the spring, install a wood spacer under the old baseplate, and then install the new baseplate under the spacer, should allow me to play a lot with how hard the spring is pushing. Thought about just getting new 5% extra power springs from PD (couldn't find 10% mentioned above) but this was cheaper and should allow me to play a bit more. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 23, 2019 Share Posted July 23, 2019 (edited) Replace your mag springs. This is the first sign they’re getting weak. I *theorize* that what happens is the stack of rounds in the mag bounces back downward a millimeter or so when you seat the mag due to the weakening spring, and your slide closes over top of them. However. I can say from actual experience (on two different gun platforms, neither of which was Tanfo) that replacing the mag springs fixed my “dry chamber auto forward” issue. Edited July 23, 2019 by MemphisMechanic Link to comment Share on other sites More sharing options...
lstange Posted July 23, 2019 Share Posted July 23, 2019 I would also check the surface on the notch in the slide that the slide stop engages, maybe that corner got rounded. When trying to reproduce autoforward the angle of the hit is more important than the force of the hit. It's the forward component that pushes the frame forward, while inertia keeps the slide back, unloading the slide release and letting its spring to drop it. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted July 23, 2019 Author Share Posted July 23, 2019 1 hour ago, MemphisMechanic said: Replace your mag springs. This is the first sign they’re getting weak. I *theorize* that what happens is the stack of rounds in the mag bounces back downward a millimeter or so when you seat the mag due to the weakening spring, and your slide closes over top of them. However. I can say from actual experience (on two different gun platforms, neither of which was Tanfo) that replacing the mag springs fixed my “dry chamber auto forward” issue. 1 hour ago, lstange said: I would also check the surface on the notch in the slide that the slide stop engages, maybe that corner got rounded. When trying to reproduce autoforward the angle of the hit is more important than the force of the hit. It's the forward component that pushes the frame forward, while inertia keeps the slide back, unloading the slide release and letting its spring to drop it. I like this forum. Thought about just installing new mag springs, thought the spacers was more of a nuclear option but might find out that just springs would have been better. Darn encouraging to know that you have fixed the problem that way. Slide looks square as brand new. Might be a good idea for me to play some more with angle of the hit. Thought I was duplicating every sort of match reload but it has got to be something. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted August 2, 2019 Author Share Posted August 2, 2019 On 7/23/2019 at 8:48 AM, IHAVEGAS said: I'm going to keep the old baseplates attached to the spring, install a wood spacer under the old baseplate, and then install the new baseplate under the spacer, should allow me to play a lot with how hard the spring is pushing. Thought about just getting new 5% extra power springs from PD (couldn't find 10% mentioned above) but this was cheaper and should allow me to play a bit more. For what it is worth. Doing the above, so far seems to have fixed the issue. My guns have always been a bit wonky about slamming in a slide stop reload, I think but do not know that having a bit of extra tension when only loading to 10 rounds might be a good thing for Tanfo's as a general rule. Confirmed with PD that the 5% extra power springs do not fit the stock end plates without bending. That might not be much of a problem but I decided I wouldn't mess with it unless a need arises, putting a new bend shape in spring steel can be ornery sometimes. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now