f2benny Posted March 3, 2019 Share Posted March 3, 2019 Brain trust what do you make of this. My buddy was shooting his SP01 tac with a milled slide by CGW and a DPP. At the end of the stage after the last shot the slide release fell to the ground and the slide moved half way down the slide. The slide stop was not broken or unusual in any way. The recoil spring and guide rod were assembled on the barrel and slide and there was a live round in the chamber. We disassembled the gun at the safe table and everything looked normal. Once it was put back together it shot 2-3 more stages without any issue. I've never seen anything like that before. Any thoughts how that could occur? The slide stop was snug in the gun once it was assembled again too. Link to comment Share on other sites More sharing options...
Rnlinebacker Posted March 3, 2019 Share Posted March 3, 2019 Brain trust what do you make of this. My buddy was shooting his SP01 tac with a milled slide by CGW and a DPP. At the end of the stage after the last shot the slide release fell to the ground and the slide moved half way down the slide. The slide stop was not broken or unusual in any way. The recoil spring and guide rod were assembled on the barrel and slide and there was a live round in the chamber. We disassembled the gun at the safe table and everything looked normal. Once it was put back together it shot 2-3 more stages without any issue. I've never seen anything like that before. Any thoughts how that could occur? The slide stop was snug in the gun once it was assembled again too.slide stop might have started walking out slowly while shooting. hopefully doesn't happen againSent from my SM-N950U using Tapatalk Link to comment Share on other sites More sharing options...
yigal Posted March 3, 2019 Share Posted March 3, 2019 check that spring that holding slide stop in place is ok. Link to comment Share on other sites More sharing options...
muncie21 Posted March 3, 2019 Share Posted March 3, 2019 (edited) 13 minutes ago, yigal said: check that spring that holding slide stop in place is ok. OP- it's #3 in the parts diagram SP01_9MM.pdf Edited March 3, 2019 by muncie21 Link to comment Share on other sites More sharing options...
yigal Posted March 3, 2019 Share Posted March 3, 2019 1 hour ago, muncie21 said: OP- it's #3 in the parts diagram SP01_9MM.pdf 149.42 kB · 0 downloads yes .correct. find once cracked part#3 but not broken. and #4 was missing. all this parts can make SS go out. Link to comment Share on other sites More sharing options...
mro111lland Posted March 4, 2019 Share Posted March 4, 2019 could have ben riding the slide stop pin where it protrudes throught the side on the right side and pushed it out Link to comment Share on other sites More sharing options...
Joedirt199 Posted March 6, 2019 Share Posted March 6, 2019 That slide stop nub is pretty far forward to be riding with anything. It's hard enough to push the slide stop out with a fully functioning detent spring to keep it in. My money is on #4 is missing or broke since it keeps the tension on the spring to hold the slide stop in place. Link to comment Share on other sites More sharing options...
muncie21 Posted March 6, 2019 Share Posted March 6, 2019 3 hours ago, Joedirt199 said: That slide stop nub is pretty far forward to be riding with anything. It's hard enough to push the slide stop out with a fully functioning detent spring to keep it in. My money is on #4 is missing or broke since it keeps the tension on the spring to hold the slide stop in place. ^^ Yep that's where my money is also Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now