Jump to content
Brian Enos's Forums... Maku mozo!

Joedirt199

Classified
  • Posts

    187
  • Joined

  • Last visited

Everything posted by Joedirt199

  1. Wondering if anybody has modified their delayed buffer with a short stroke kit? I was looking into it and it would benifit from it greatly as the bolt leaves a lot of empty space behind the bolt stop for brass to accidently end up. When looking at the buffer setup, the bumper is built into the rear of the recoil rod so a spacer would need to be fitted over the spring between the rear bumper and roller buffer. Anyone tackle this yet? I have an email into Maxim and JP to see if they have any ideas or have considered it. One person said he made one out of delrin on reddit.
  2. I received an updated bolt from CMMG to try but after reading from others who got the bolt and had the same ejection problems arrise after a few hundred rounds, have decided to abandon the CMMG radial system and just use PSA AR-V receiver set with Maxim Defense Delayed Buffer system. No ejection problems and uses 35 rd Evo mags. I do run it suppressed 100% and it has been way more satisfing then CMMGs RDB offering.
  3. Are you using mixed or sorted by headstamp brass? Nevermind I see you are using Sig brass in batches.
  4. I have the EPS direct mounted to my 48 MOS. You just have to remove the back nubs with a dremel tool and shorten the front nubs with a couple strokes of a file and it will direct mount with the stock MOS screws. It hangs over the sides a little more than the EPS Carry but not by much. The 6 MOA dot works best for my bad eye sight and has the least amount of star bursting.
  5. I use the PRI gas buster with the large latches on mine and it makes it easier to charge with more fingers on the levers. Keep the stock in your shoulder so the gun has a something hard to press against while charging.
  6. My back was to the direction arrow I need to go and when I came back to the stage for the second time, he had no problems telling me to get a compass mate. Still managed to rank pretty well with the extra mile. Always a good time and one thing I look forward to each year.
  7. I come to hear the special forces guys tell me "good shooting man." Plus the money goes to a worthy cause. They also have no problems busting your chops for going the wrong way out of a stage and adding a mile to your already long 10k.
  8. I was rooting for some of the core group to just die off already since they caused more harm then good and were annoying to the story line.
  9. Works like a charm on my shadow 1
  10. Yup all direct rmr mounted. They measure your optic to make sure it is within the tolerances of their milling cuts. Optic actually snaps into place so very little stress on the screws.
  11. Primary Machine Have 3 slides done by them all perfect and fast turn around
  12. Holiday weekend didn't help. Hard to compete with opening season for lake of the ozarks.
  13. Following this as well since my reddots are not as crisp as they should be. Tried on my wife's glasses and they did clear up. Going to try the magnified safety glasses route by buying different strengths and see what works. Only ones I found were elvex rx-500c as they have a split lens construction and have full lens magnification. I can mix and match the lenses to find the right combo for my eyes. They only cost about $8.
  14. Yup hot nasty both days. Tough stages for everyone level of skill. Thanks again guys and gals
  15. Doubt a 510 will fit a mounting MOS plate and it is too big for slide mount. Need a 507/407 footprint
  16. So how muddy nasty are the bays going to be? Trying to gauge how many pairs of shoes I need to bring
  17. I have got really good sd's with 244 in the 4-4.1 range with 124 bullets. Very consistent with jacketed and lead coated. Doesn't matter where I am at in the powder range, always single digit sd's.
  18. Yeah IL sucks since Chicago runs the whole state. Was suposed to shoot the Spartan 300 with some buddies from work and now that the state is still on lockdown, they moved the match to october. That conflicted with their schedule and had to drop out.
  19. Just got an email saying they are caught up on the 124 FP matches and the HP are close. 147 RN is still running strong trying to get orders out.
  20. 4.5 of HP38 is my load wich is the same as 231. 1100 fps out of my fullsize CZs. Same OAL.
  21. Didn't help that the craze/election drove people to raid ammo stores making most places out of stock. Got my RMR bullets a month after ordering and plenty of time to load a stash for this match. Also people may not be getting paid durring their forced time off making budget tight.
  22. Can't go wrong with Primary Machine. Fast turnaround, tight milled pocket, flawless cerakote. Have 2 P-series CZs done by them and just sent off a glock slide.
  23. Just over a month for mine. Got them yesterday, ordered on march 24. No shipping email they just showed up.
  24. I did 11mm deep socket with extension down in it long enough to stick up from the hammer side of slide that you can grip the slide and extension in one hand squeezing them together. Drill a 3/4" hole in a piece of 2x4 so the stock bushing will move into the hole as you hammer it out and the board will protect the muzzle of the slide. Heavy hammer helps.
×
×
  • Create New...