speedy169

That s not true. My buddy has a left hand DOH for a 9L. You may have to order from Blade Tech.

Does anyone know of a place that can source an M&P slide for a reasonable price. I really don't want to buy another whole gun but if that is my only option. I have had this idea that I wanted to try but I don't want to buy a whole gun then figure out that it won't work and I have just trashed a slide. I wish that Caspian or some one else would make replacement slides like they do for the G-Locks.

Any idea on a release date? What other cool stuff do you guys have planed for the future? Titanium Strikers maybe? What was wrong with the original design?

I thought I saw this on the SSS Website a few weeks ago and now it is gone. Can some one verify this. I was going to get one to try but it is not there now. Thanks

Sounds like you have a good setup in the gear department. As for the trigger a good polish of all the matting surfaces makes a huge difference, but a trigger job from some of the pros is just awesome. I have not had many problems with leading in my M&P 40 but I shoot it more minor than major at the moment. Until they release a Long Slide model we are at a disadvantage. I have not had any problems with FTF except for when I went to the lighter striker spring. I have heard the 1050 primer setup is a little tuff to dial in.

They make a CR Speed holster for the XD. I think it is the same as the Glock one. I modded my 1911 CR holster to fit my M&P. Just removed the spacers and did a little dremel work. Here is a link to the post I made about it. Scroll down lots of pics. http://www.brianenos.com/forums/index.php?showtopic=88124

Does Dan do Hard Crome? I like the looks of a two tone pistol. I am curious of cost to have the slide redone.

A Bomar style sight sounds and looks very doable on an M&P. You wouldn't be able to sink it into the slide very much because of the Firing Pin Block. Burwell machined a slide to take a slide ride Red Dot so he may have some thoughts on this.

Tac Sol is saying that the 22 conversion should be out by 1st quarter of 2010. As for the 40L. I am just keeping my fingers crossed that they will make them. I want one in a bad way.

Your dremel changed the colour??? The green one is a 1911 holster. It was just green with envy.

The fit is great. Nice and tight but still just right for a smoth draw. The only thing to note is that you need to flip the muzzel platform or cut some out of it to clear the rail on the M&P. It fits tight and snug. I ran up and down the stairs, jumped up and down, and ran around with the holster unlocked and locked to see if it would fall out or wiggle lose. I plan to use it in my first match this weekend so we will see how it does. Hope this helps some one else out. I see 1911 CR Speed holsters in the for sale section alot for around $100.

So then I tryed the M&P out in the Glock Holster and it rattled and just didn't fit good. Some Dremel work and and cutting might make it better. Then I tryed the M&P in the 1911 CR Speed with out the shims and thought I could make it work easier. About 5 minutes with the dremel and this is waht I ended up with. A closser look at what I had to do. A little chamfer around the trigger gaurd area and some relief in the front and I was good to go.

Ok, I did some leg work and this is what I came up with. M&P in a Bladetech DOH. Just to see what I started with. A call to CR Speed turned up that the Glock Holsters will accept the M&P and the XD. I dug up an old Glock Holster from a friend and started looking it over. The trigger gaurd area is wider than a 1911 style CR Speed. The 1911 CR Speed holster as a shim stack that can come out to except a wide trigger gaurd.

I know ther are some people out there using the CR Speed holster. Come on people whats the details to make this work.

What mods need to be done to make the M&P fit in the CR Speed holster? I have the 1911 model CR Speed that I want to use, but it looks like it is going to need some major mods to work.