Albertito Posted July 11, 2009 Share Posted July 11, 2009 I would lke to know how to remove the bulge on 45 brass in wont go in the gage tool. I am using a dillon 550 Link to comment Share on other sites More sharing options...
Steve J Posted July 11, 2009 Share Posted July 11, 2009 Are you full length sizing it? Check your sizing die adjustment. Link to comment Share on other sites More sharing options...
WyoBob Posted July 11, 2009 Share Posted July 11, 2009 Bulge at base or bulge due to bullet insertion? If the bulge is due to bullet insertion, if the loaded round chambers, I don't think you have anything to worry about. In fact, I think it's a good thing. You have a tight grip on the bullet which will go a long way toward eliminating bullet setback. If the bulge is at the case head end--- What Steve J said. WyoBob Link to comment Share on other sites More sharing options...
Albertito Posted July 11, 2009 Author Share Posted July 11, 2009 Bulge at base or bulge due to bullet insertion? If the bulge is due to bullet insertion, if the loaded round chambers, I don't think you have anything to worry about. In fact, I think it's a good thing. You have a tight grip on the bullet which will go a long way toward eliminating bullet setback.If the bulge is at the case head end--- What Steve J said. WyoBob Link to comment Share on other sites More sharing options...
Albertito Posted July 11, 2009 Author Share Posted July 11, 2009 The die set is from Dillon Part # 14404 kit. The die is all the way down toward shell plate. The bulge is at the bottom. Link to comment Share on other sites More sharing options...
HRider Posted July 11, 2009 Share Posted July 11, 2009 Is the brass from your pistol? I have seen pistols that had been "throated" to the point that there was no support far enough into the chamber that every case that came out of the gun was bulged badly. This is a dangerous situation, as case rupture can detonate rounds in the magazine. I use Dillon dies in my 650 and load 45acp. I pick up range brass and other than brass out of some pistol like I mentioned above, I have not had any problems with case bulging (I shoot a Colt 1911 w/o a ramped barrel). One of the guys in my club likes a Lee sizing die because it is not chamfered as far in as the Dillon die. He loads 45acp for revolver and says the lee die helps his rounds drop in and out of the cylinder better (I have a 625 also and have not had any trouble using my Dillon dies). I hope this helps, Hurley Link to comment Share on other sites More sharing options...
LPatterson Posted July 13, 2009 Share Posted July 13, 2009 If you want to remove the bulge so all rounds fit in the case guage contact Lee for an undersize die, call in not on website. If it is hanging up at the rim, turn the round over and insert the base first into the case guage and wiggle it around. This usually smooths out the rim allowing the round to drop into and out of a case guage. Link to comment Share on other sites More sharing options...
redwoods Posted July 13, 2009 Share Posted July 13, 2009 If the 45 brass is from a glock, it would be "glocked brass". The barrel chamber is open near the base more than other guns. The bulge happens more with glock barrels than others. To get the rounds to case gauge, I bought a Lee Undersize Die for my 40sw, you can buy one from www.egwguns.com. I reload 45acp glocked brass using a dillon die and it loads fine in my 1911. For my 40 and 9, I use the Lee Undersize Die from EGW. I don't have any problems with 45acp using my dillon die. Randy Link to comment Share on other sites More sharing options...
Albertito Posted August 1, 2009 Author Share Posted August 1, 2009 I called Lee ordered crimp die to fix the problem. Link to comment Share on other sites More sharing options...
Dave Gundry Posted August 1, 2009 Share Posted August 1, 2009 If it is not from your gun, but still chambers in your gun, just load it and shoot it - skip the guage. After firing, the bulge won't matter. Link to comment Share on other sites More sharing options...
CSEMARTIN Posted August 1, 2009 Share Posted August 1, 2009 I called Lee ordered crimp die to fix the problem. I don't think the crimp die will get you any further down on the case than your sizing die in station 1. I think this will help you: http://egw-guns.com/store/index.php?main_p...;products_id=40 Link to comment Share on other sites More sharing options...
Albertito Posted August 6, 2009 Author Share Posted August 6, 2009 I spoke with a Lee rep and he sold me a under size die to fix the problem. I will let you kow if it work. Link to comment Share on other sites More sharing options...
Albertito Posted August 8, 2009 Author Share Posted August 8, 2009 Well the dies came in and guess what it work the bulge is all gone. Link to comment Share on other sites More sharing options...
Paul Burtchell Posted August 8, 2009 Share Posted August 8, 2009 Link to comment Share on other sites More sharing options...
Steel Shootist Posted August 9, 2009 Share Posted August 9, 2009 I gave up on my case gauge for my .38 super (and all my other pistol rounds) quite a while ago. I couldn't get many to fit in the case gauge but nearly ALL fit into the chamber of my gun that I would be shooting them out of. As long as they fit in your chamber, that's what really matters. It's way easier if you take the barrel out of your gun (you take it out to clean it anyway) and just drop them in one at a time. Your case gauge may be a little undersized too...that won't help them fit either. Just my 2 cents.... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now