Matt Griffin Posted May 26, 2008 Share Posted May 26, 2008 I'm figuring post -2, but are frame mount pins or hammer mount pins better, and are there any differences beyond that? H. Link to comment Share on other sites More sharing options...
cas Posted May 27, 2008 Share Posted May 27, 2008 The -3's will still have the silly floating hand. Not the worst thing in the world to replace, but obviously easier if you don't. Link to comment Share on other sites More sharing options...
Bubber Posted May 27, 2008 Share Posted May 27, 2008 Houngan, I'm not an expert but it makes lettle difference. You can go lower on DA pull with the frame mounted. I used to think the other way until I tried a few of the frame mounted ones. I don't use the 625 even though I have one. I am not happy with the way "I" can shoot it. I use the L frame revos. Link to comment Share on other sites More sharing options...
kframe_mike Posted May 27, 2008 Share Posted May 27, 2008 Houngan, I'm not an expert but it makes lettle difference. You can go lower on DA pull with the frame mounted. I used to think the other way until I tried a few of the frame mounted ones. I don't use the 625 even though I have one. I am not happy with the way "I" can shoot it. I use the L frame revos. I'm in the same boat Bubber.I can shoot a N frame pretty quick,or I can shoot an N frame pretty accurately,just not both at the same time.And as far as reloads go,I'm so slow the big holes and good moonclips are a wash too.Mike mine a K or L please.-Mike Link to comment Share on other sites More sharing options...
Carmoney Posted May 27, 2008 Share Posted May 27, 2008 The -3's will still have the silly floating hand. Not the worst thing in the world to replace, but obviously easier if you don't. Most of the 625-3s I've seen do not have the floating hand. That was actually one of the design changes when they switched to 625-3, but some of the earlier guns left the factory with the floating hand. (Typical of S&W, they always try to use up everything they have laying around, even when they know if doesn't work real well....) The floating hand is pretty easy to fix, just take off the hand, pull the pin, and replace with a traditional hand. For a gun to shoot, I wouldn't avoid anything other than a 625-2 (and I wouldn't avoid one of those if the price was right). My personal favorite of the lot is the 625-6, which in .45 ACP is generally found with a frame-mounted FP and (gasp!) MIM parts, but no key-lock. Link to comment Share on other sites More sharing options...
David Sinko Posted May 27, 2008 Share Posted May 27, 2008 Many shooters who have guns with frame mounted firing pins complain bitterly that they can not fire loose rounds and are useless without the moonclips. All three of my 625s are -4 versions with hammer mounted firing pins and they DO fire loose rounds. I even trimmed some brass to see how short I can go and it fired everything DA, including .45 GAP as long as the gun wasn't pointed straight down. Most competitive shooters won't care about this, but all my revolvers see service use so I always seek out revolvers with hammer mounted firing pins. Dave Sinko Link to comment Share on other sites More sharing options...
HighVelocity Posted May 27, 2008 Share Posted May 27, 2008 I have 2 625-3's. One has the floating hand, the other does not. Both have hammer mounted firing pins. Both run 100% and fire all 45acp cartrdges, regardless of primer brand and with or without moonclips. Sure, the triggers could be slicker, lighter, etc. But they're good enough for me. Gary Link to comment Share on other sites More sharing options...
Daniele Posted May 27, 2008 Share Posted May 27, 2008 625-3's. One has the floating hand, the other does notGary I have one "model of 1989 625", don't know the -#,it is a hammer mounted firing pin, don't even know what exactly is a floating hand and why the regular one is lot better. Please explain. Link to comment Share on other sites More sharing options...
jjanglin Posted May 27, 2008 Share Posted May 27, 2008 Seems "MIM" parts have and undeserved bad name the only ones that Ive ran into that are junk are some of the Para early parts and I cured that problem with having them cryo treated, Ive sorta just started to mess with S&W revolvers see no problem with their MIM parts if I should doubt some of them Id take them over to the CRYO place and get em froze up. Jim/Pa Sailaors Link to comment Share on other sites More sharing options...
Matt Griffin Posted May 27, 2008 Author Share Posted May 27, 2008 625-3's. One has the floating hand, the other does notGary I have one "model of 1989 625", don't know the -#,it is a hammer mounted firing pin, don't even know what exactly is a floating hand and why the regular one is lot better. Please explain. Open the cylinder and look inside at the frame where the yoke enters, you'll see the -X number designation. Mine's a -4, and I'm in the market for a backup gun, or a primary if I can get the trigger even lower. Since these are strictly competition guns, trigger pull does make a big difference in ease of use. H. Link to comment Share on other sites More sharing options...
cas Posted May 27, 2008 Share Posted May 27, 2008 My 1990 vintage (Model of 1989) -3 had the floating hand. Link to comment Share on other sites More sharing options...
Carmoney Posted May 28, 2008 Share Posted May 28, 2008 Ive sorta just started to mess with S&W revolvers see no problem with their MIM parts if I should doubt some of them Id take them over to the CRYO placeand get em froze up. Watch out for those cryopractors....always trying to convince you to do more treatments and pay more money! Link to comment Share on other sites More sharing options...
EEH Posted June 2, 2008 Share Posted June 2, 2008 The -3's will still have the silly floating hand. Not the worst thing in the world to replace, but obviously easier if you don't. Most of the 625-3s I've seen do not have the floating hand. That was actually one of the design changes when they switched to 625-3, but some of the earlier guns left the factory with the floating hand. (Typical of S&W, they always try to use up everything they have laying around, even when they know if doesn't work real well....) The floating hand is pretty easy to fix, just take off the hand, pull the pin, and replace with a traditional hand. For a gun to shoot, I wouldn't avoid anything other than a 625-2 (and I wouldn't avoid one of those if the price was right). My personal favorite of the lot is the 625-6, which in .45 ACP is generally found with a frame-mounted FP and (gasp!) MIM parts, but no key-lock. what about the trigger on newer modles like the 625-8 R they OK. Link to comment Share on other sites More sharing options...
Carmoney Posted June 2, 2008 Share Posted June 2, 2008 They're fine. You can get a very nice action with a 625-8. Link to comment Share on other sites More sharing options...
jjanglin Posted June 3, 2008 Share Posted June 3, 2008 Ive got some Para LDA's out their with some pretty nice triggers on them,Its hard as heck to get the sears to stay at the right angle unless I have them cryogenically treated,Ive also done some of para's barrels in a before an after grouping= all the barrels I did this with tightend up with grouping after the cryo treat. Im sold on the process, the fella I have do this treating does cutting blades of various kinds for conagra and they say it improve the life of the blades as much as 40 %.He Does airplane engine parts for those folks who race the pylons seen some of their dyno test results it is allmost unbeleavable. Jim/Pa Sailors Link to comment Share on other sites More sharing options...
inkedshooter Posted June 3, 2008 Share Posted June 3, 2008 I had a 625-8. I installed Jerry's spring set up in it and made for a very nice trigger pull. I did have some problems with factory Winchester, Remington shot ok, Reloads with Federal primers shot great. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now